Hydrocarbon delivery rubber hoses

Intended for suction and delivery of tar, bitumen and hot petroleum products, hose 401 has excellent resistance to ozone and bituminous products thanks to the quality of its covering.
The hose structure is protected from heat by a fibreglass interlayer and it has a low bend radius.
It can be supplied equipped with half-symetrical, threaded or flange fittings along with ADR test certificate.
- In Ø 19, Its reinforcement consists of two metal wire spirals.
- In Ø 25 is protected by an external metal spiral  and produced in predetermined lengths with flexible cuff-ends.
- In Ø 38, 50 and 63 have a smooth outer cover and can be cropped to length.
- In Ø 50, we offer a variant identical to Ø 25.

Technical specifications :
Inner tube : smooth black synthetic rubber
Reinforcement : fibreglass protection, textile plies and metal spiral
Outer cover : abrasion and weather resistant CR / NBR rubber
Outer finish :
- Ø19, Ø 38, Ø 50 et Ø 63 : smooth
- Ø 25 : ondulé (external metal protection spiral for Ø 25 and 50)
Temperature : + 180°C max
Production lengths : 40 metres. Ø 25 : 5, 8, 15 meters
Electrical conductivity : 1 copper braid or external spiral
Colour : black
Particularities : oversized cuff-ends Ø 25, 50

Possible end-fittings : Male threaded, Guillemin
See also Part N° 402, 411
* In accordance with Appendix IV.1 of the modified TMD Order of May 29, 2009

The hose 403 is intended for the equipment of the reels of the fuel distribution tankers.
Manufactured in accordance with the EN 1360: 2013 standard, in the lightest possible way, it has a very thin striped rubber coating very resistant to abrasion.
We deliver it fitted with male or female male or female BSPP fittings 1''1/2 in steel and certificates in accordance with Appendix IV-1 of the amended TDG Order of May 29 2009.
The male threaded end is equipped with a bending spring.

Technical specifications :
Inner tube : black NBR noir rubber conductor
Reinforcement : 2 textile plies
Recouvrement : caoutchouc synthétique
Outer finish : wrapped
Electrical resistance : less than 1 Mega Ω per meter
Temperature : - 30°C to 70°C
Production length: 50, 60 meters
Colour : black
Red tape marking : Tecalemit - 403 - Hydrocarbures - 16 bar
Inlay marking : SEL - 403 35 - EN1360:2013 - Type 1 - 35 mm - 16 Bars - Ω - TRIM/AN - N° Lot

* In accordance with Appendix IV.1 of the modified TMD Order of May 29, 2009

Hose 405 is intended for conveying fuels with up to 50% aromatic content (lead-free fuel).
It complies with DIN 73379: 199 version 2A
Its inner tube is antistatic and is available in coils for automobile garages and builders.

Technical specifications :
Inner tube : black antistatic nitrile rubber
Reinforcement : textile braid
Outer cover : CR
Outer finish : smooth
Temperature : - 30°C to + 90°C
Production lengths : 50 metres
Colour : black
Marking : Tecalemit - 405 - DIN 73379 type 2A - dia. x thickness - NBR/CR - batch N°
Particularity : antistatic

Possible end-fittings :Threaded, CB range
See also Part N° 407, 406

Hose 406 is intended for conveying fuels with up to 50% aromatic content (lead-free fuel).
Its inner tube is antistatic.
Its hypalon outer cover allows use of this hose in 110°C continuous atmospheres with peaks up to 135°C.
This outer cover also has excellent resistance to aging and ozone effects..

Technical specifications :
Inner tube : black antistatic NBR rubber
Reinforcement : textile braid
Outer cover : CSM
Outer finish : smooth
Temperature : - 30°C to + 90°C
Production lengths : 25 or 50 metres
Colour : black
Marking : Tecalemit - REF 406 - DIN 73379 type 2B - dia. x thickness - NBR/CSM - batch N° - month/year
Particularity : antistatic

Embouts utilisables : filetés, gamme CB

Hose REF 411 is intended for suction and delivery of tar, bitumen and hot petroleum products.
The quality of its outer cover affords excellent resistance to ozone and bitumenous products.
It has a low bend radius.
It can be swaged with threaded fittings.

Technical specifications :
Inner tube : black synthetic rubber
Reinforcement : textile plies and metal spiral
Outer cover : abrasion and weather resistant microperforated CR / NBR rubber
Outer finish : wrapped
Temperature : +80°C
Production lengths : 40 metres
Electrical conductivity : 1 copper braid
Colour : black
Marking : Tecalemit - 411 - emulsion de bitume 80°C - production date or batch

Possible end-fittings : Male threaded with male union 1”1/4, male threaded 3/4 with female union 1”1/4

The 416 GGE hose is intended for hydrocarbons at a pressure of 10 or 14 bar and has 2 galvanized steel coils and a polypropylene tube.
The 416 AAE hose is the same hose but in a light version because it has 2 aluminium coils, and its working pressure is 10 bar.
The 416 SST hose, with a working pressure of 14 bar, is suitable for many chemicals as its coils are made of 316L stainless steel and its tube is PTFE.
We fit these hoses with aluminium, bronze, or stainless-steel end caps, as well as flange connectors, according to the different international classes.

Technical specifications :
Inner tube : polypropylene film
Renforcement : Multiple polyester films between two helical turns in galvanized steel
Reinforcement : textile PVC coated
Outer finish : smooth with external metal protection spiral
Temperature : - 30° à + 100° c
Production lengths : 30 metres
Colour : black with red stripe
Marking : Tecalemit - 416 - PS bar - (trimester/year) - batch N°

Possible end-fittings : Guillemin, Camlock, Flanges, B.S.P
* In accordance with Appendix IV.1 of the modified TMD Order of May 29, 2009

The hose 443 is intended for the equipment of petrol pumps for diesel, biofuels, standard gasoline , ”super” as well as unleaded gasoline.
The 443T version has a textile reinforcement and complies with EN 1360 type 1.
The 443M version has a metal braid and complies with EN 1360 type 3.
The hose is available in different colors and with a conductive tube of
electricity (resistance to the meter less than 1 Ω m).

Technical specifications :
Inner tube : NBR black
Reinforcement : Textile braid (443T) - Steel braid (443M)
Outer cover : Oil-resistant and weather-resistant rubber
Outer finish : Smooth or wrapped
Temperature : -30°C to +55°C (on request -54°C to +85°C)
Production lengths : variables
Colour : black, green, red or blue
Marking : TECALEMIT - 443 - EN1360: 2013 - TYPE (1 or 3) - Ω - Ø - WP 16 BARS - (QUARTER / YEAR) - BATCH N°

Possible end-fittings :Threaded,

Hose 462 is particularly appreciated by industrial site maintenance services.
It accepts hot glycol water, compressed air, oil and hydrocarbons up to 40% aromatic content.
It has static electricity conductiveness.
Its reinforcement and thickness give it excellent bend radius.

Technical specifications :
Inner tube : antistatic NBR rubber
Reinforcement : textile braid
Outer cover : CR / SBR rubber
Outer finish : smooth
Temperature : - 30°C to +70°C maximum
Production lengths : 25 or 50 metres
Colour : black
Marking : Tecalemit - part N° - tuyau multiservice/multipurpose hose - antistatic - ps/wp 25/350psi - DN (mm/inch) - batch N

Possible end-fittings : Threaded, CB range
See also Part N° 461, 362, 405

The 489 hose is especially conceived for the ground refuelling of aircrafts having an aromatic content up to 50 %.
It meets EN 1361 type B standard.

Technical specifications :
Inner tube: aviation gasolines and jet fuels resistant,conductive NBR rubber.
Reinforcement : high tensile synthetic textile and 2 antistatic copper wire.
Outer cover: abrasion,ozone,weather,heat and oil resistant special synthetic rubber.
Production lengths : 40 & 60m.
Temperature: -30°C à to 65°C.
Electrical conductivity: < = 10⁶ Ω/m.
Outer finish : smooth.
Colour : black.
Marking : Tecalemit - Part N° - EN 1361 type B - Ω -PS 20 Bars - DN (mm/inch) - batch N°.

Intended for suction and discharge of hydrocarbons, hose 491 has 4 textile plies and a metal spiral.
It is a very robust suction hose.
It can be used over a wide range of temperatures and its neoprene outer cover ensures excellent resistance to ozone.
It is used for discharge when a low bend radius is necessary.
This versatile hose, available in many diameters, can be cut to order.
This hose can be built in several variants, with corrugated flat, corrugated or crenellated coating as well as with an operating temperature of -55 ° C to + 80 ° C.

Technical specifications :
Inner tube : black NBR nitrile rubber
Reinforcement : 4 textile plies and one metal spiral
Outer cover : abrasion and weather resistant neoprene rubber
Electrical conductivity : 1 copper braid
Outer finish : wrapped
Temperature : - 40°C to +70°C maximum
Production lengths : 20 metres
Colour : black
Marking : Tecalemit - REF 491 - aspiration refoulement hydrocarbures 10 bar - production date or batch

Possible end-fittings : Threaded, guillemin, tankwagen, flange, storz
See also Part N° 492

Hose 492 is intended for suction of oil on hydraulic powerpacks.
Economic, it can be used over a wide range of temperatures and its neoprene outer cover ensures excellent resistance to ozone.
It is used for discharge when a low bend radius is necessary.
For diameters 19, 25, 32, 38, 50, 63, 76, 100, it complies with the SAE J517 version 100R4 standard which applies to suction hoses for hydraulic oils.

Technical specifications :
Inner tube : black nitrile rubber
Reinforcement : 4 textile plies and one metal spiral
Outer cover : abrasion and weather resistant neoprene rubber
Electrical conductivity : 1 copper braid
Outer finish : wrapped
Temperature : - 40°C to +70°C maximum
Production lengths : 40 metres
Colour : black
Marking : Tecalemit - part N° - dia. - batch N°

Possible end-fittings : Threaded
See also Part N° 491

Intended for suction and discharge of hydrocarbons, hose 495 has 4 textile plies and a metal spiral.
It is a very robust suction hose.
It can be used over a wide range of temperatures and its neoprene outer cover ensures excellent resistance to ozone.
It is intended for the delivery of oil by truck - tank.
It meets NF EN 1761 type SD (suction and delivery) standard.
this hose can be swaged with guillemin end-fittings and supplied with TMD modificate (29/05/09) test certificate for which we have a flexible type approval.

Technical specifications :
Inner tube : black nitrile NBR rubber
Reinforcement : 4 textile plies and one metal spiral
Outer cover : abrasion and weather resistant neoprene rubber
Electrical conductivity : 2 copper braid (< 10⁶Ω/m)
Outer finish : wrapped
Temperature : -40°C à +70°C
Production lengths : 40 metres
Colour : black
Marking : Tecalemit - 495 - EN 1761 : 1999 SD (Ø) - PMS10 - Ω/m - CL

Possible end-fittings : Threaded, guillemin, tankwagen, flange, storz
* In accordance with Appendix IV.1 of the modified TMD Order of May 29, 2009

The 496 hoses is especially conceived for the ground refuelling of aircrafts having an aromatic content up to 50 %.
It meets EN 1361 type c standard.

Technical specifications :
Inner tube: aviation gasolines and jet fuels resistant,conductive NBR rubber.
Reinforcement: high tensile synthetic textile braid.
Outer cover: abrasion, ozone, weather, heat and oil resistant special synthetic rubber.
Production lengths : 40 & 60m.
Temperature: -30°C à to 65°C.
Electrical conductivity: < = 10⁶/m.
Outer finish : smooth.
Colour : black.
Marking : Tecalemit - Part N° - EN 1361 type C - Ω -PS 20 Bars - DN (mm/inch) - batch N°.

The 489 hose is especially conceived for the ground refuelling of aircrafts having an aromatic content up to 50 %.
It meets EN 1361 type E standard.
This hose can be produced with a thermoplastic spiral.

Technical specifications :
Inner tube: aviation gasolines and jet fuels resistant,conductive NBR rubber.
Reinforcement: high tensile synthetic textile, 2 steel wire helix and 2 antistatic copper wire.
Outer cover: abrasion, ozone, weather, heat and oil resistant special synthetic rubber.
Production lengths: 40 & 60m.
Temperature: -30°C à to 65°C.
Electrical conductivity : < = 10⁶/m.
Outer finish: smooth.
Colour: black.
Marking : Tecalemit - Part N° - EN 1361 type E - Ω -PS 20 Bars - DN (mm/inch) - batch N°.