Rubber hose – Flexible hose high pressure – Hose assemblies – Quick coupling – Flexibles for fluid transfer
BRIDE 994 raccord hydraulique

Hydraulic Flanges and components

- ISO 6162-1 and 2 /SAE rectangular flanges
- CETOP ou SID./ ISO 6164 square flanges

Principe :
This is based on inserting a compressible seal between 2 faces arranged parallel to one another, and tightly held, pressing against one another be means of bolted flanges.
The seal is exactly centred by means of a circular groove in which it is housed.
For union assembly flanges, the two faces will be flanged head end (one with a seal, the other without).
For port assembly flanges, the two faces will be on one hand the flanged head en holding the seal, and on the other the external part of the hydraulic appliance to be seal (motor, pump, jack etc...)

Advantages of using S.A.E. flanges:
- Connection capacity of tubes up to 5" external diameter (ISO 6162-1, SAE J518 code).
- For tightening the screws, slightly lower tightening torques compared with the equivalent connection threads are required.
- Low tightening torques also mean using small flat wrenches, ensuring better performance where the installation space is tight.
- Application up to 420 bars (6000 PSI) for flange sizes 1/2" to 2" (ISO 6162-2, SAE J518 code 62).
- Just one sealing point between fitting the tube/ pipe to the flanged joint.
- Easy to remove thanks to the use of split flange clamps.

Material

- Rectangular flanges one piece or two part : Wrought steel S 355** ( E 36-3 / St 52-3 ) on request stainless steel AISI 316
- Square flanges CETOP and Sid. :  S 355** steel on request stainless steel 304L ( 1.4306 ) or 316L ( 1.4306 )
- ISO / SAE Blocks : C35/C45 steel ( XC38/48 – CK35/45 ) on request stainless steel 304L ( 1.4306 ) or 316L ( 1.4306 )
- Flanged head to be welded : S 235** steel ( E24 / St 37 ) on request stainless steel 304L ( 1.4306 ) or 316L ( 1.4306 )
- Standard 0"Rings : Perbunan / Viton* 90 Shore A
- Flange plugs and Threaded flanged head : S 235** steel ( E24 / St 37 ) on request stainless steel 304L ( 1.4306 ) or 316L ( 1.4306 )
- Métric / UNC CHC bolts : Class 12.9 quenched steel
- Nuts : Class 10 quenched steel

Normalizations

SAE TYPE RECTANGULAR FLANGES AND FLANGED
HEAD TO BE WELDED		 NORM ISO
(NORM AFNOR)
NORM U.S.A.		 ISO 6162-1 and 2 to 2002
( NF E 48-055 12/86 )
SAE J 518
CETOP AND SIDERURGIE TYPE SQUARE FLANGES AND
FLANGED HEAD TO BE WELDED		 AFNOR
RECOMMENDATION		 NF E 48-054 12/98
CETOP RP 63 H
ISO 6164 05/94
METRIC BOLTS AND NUTS AFNOR
DIN
U.S.A.		 NF EN ISO 4762 12/97
912
According to American standard
0-RINGS USA
AFNOR		 SAE J 515
NF T 47 501 04/98

Flange types

Brides carres

CETOP or SIDERURGIE type square flanges (Figure 3) (square arrangement of fixing bolts)
One piece only
Brides SAE

SAE type rectangular flanges (Fig.1 and 2) (rectangular arrangement of fixing bolts)
One piece or in two parts.

Machining

Flanges Flanges head
Untreated external surfaces
Internal face Ra = 6,3
Reaming Ra = 6,3		 All external sections Ra = 6.3
Pass Ra = 6,3
Bearing surfaces of seals and grooves Ra = 1,6

Protection

- Flanges and Split Flanges ISO 6162 / SAE : Galvanizing-bichromating
- Square flanges : Phosphatization or oiling
- Test Flanges ISO 6162 / 6164 : Galvanizing-bichromating
- Flanged head to be welded and plug flange : Oiling or Phosphatization
- Threaded flanged head : Galvanizing-bichromating
- Nuts and bolts : Burnishing
- Connection Blocks : Oiling

Tightening torque

Metric screw

Dia. screws M 6 M 8 M 10 M 12 M 14 M 16 M 18 M 20 M 22 M 24 M 27
Couple Maxi da Nm 1 3,2 7 13 14,9 23 32 45 61 71 110

 

UNC screw
Dia. screws 5/16" 3/8" 7/16" 1/2" 5/8" 3/4"
Couple Maxi da Nm 3,5 6,3 10 15,6 30 49

the following tightening torques are given as an indication

Sealing

Standard version connections are sealed with Perbunan Shore A 90 0'Rings.
The choice of seal is determined by the liquid carried as well as the operating temperature

LIQUIDS CARRIED OPERATING TEMPERATURE MATERIAL
Mineral oils, water diluted with soluble oil - 30° + 110° C PERBUNAN
Flammable hydraulic oils, oils at high temperatures - 20 ° + 200° C VITON* ELASTOMERE FLUORE

Contact us for other liquidds or other temperature
* Dupont de Nemours trademark.


Rectangular flanges - SAE 3000 / SAE 6000

Flanges and split flanges

+ -

FLANGES SAE 3000 / SAE 6000
BRIDE 994 raccord hydraulique
   
Click to collapse
BRIDES RECTANGULAIRES MONOBLOC
FLANGES ACCORDING TO THE ISO 6162-1 / SAE 3000
Part N° PN bar1 DN F Ø D Ø J U Ø T GG Q FF O Bolts
Metric UNC
BM-3000-3/8"-M 350 10 6.2 24.9 18.7 14 8.7 16.5 35 40 50 8 -
BM-3000-1/2"-M/U 350 13 6.2 31 24.3 13 8.7 17.5 38.1 46 4 8 5/16"
BM-3000-3/4"-M/U 350 19 6.2 38.9 32.2 14 10.5 22.3 47.6 52 65 10 3/8"
BM-3000-1"-M/U 315 25 7.5 45.3 38.5 16 10.5 26.2 52.4 59 70 10 3/8"
BM-3000-1"1/4-U 250 32 7.5 51.6 43.7 14 12 30.2 58.7 73 79.5 - 7/16"
BM-3000-1"1/4-M 250 32 7.5 51.6 43.7 14 12.5 30.2 58.7 73 79.5 12 -
BM-3000-1"1/4"-M/ISO* 250 32 7.5 51.6 43.7 14 10.5 30.2 58.7 73 79.5 10 -
BM-3000-1"1/2-U/ISO* 200 38 7.5 61.1 50.8 16 13.5 35.7 69.8 83 94 12 1/2"
BM-3000-1"1/2-M 200 38 7.5 61.1 50.8 16 14.5 35.7 69.8 83 94 14 -
BM-3000-2"-U/ISO* 200 51 9 72.3 62.8 16 13.5 42.9 77.8 97 102 12 1/2"
BM-3000-2"-M 200 51 9 72.3 62.8 16 14.5 42.9 77.8 97 102 14 -
BM-3000-2"1/2-U/ISO* 160 64 9 84.9 74.9 19 13.5 50.8 88.9 109 114.5 12 1/2"
BM-3000-2"1/2-M 160 64 9 84.9 74.9 19 14.5 50.8 88.9 109 114.5 14 -
BM-3000-3"-M/U 138 76 9 102.4 90.9 22 17 61.9 106.4 131 135 16 5/8"
BM-3000-3"1/2-M/U 35 89 10.7 115.1 102.4 22 17 69.8 120.7 140 152 16 5/8"
BM-3000-4"-M/U 35 102 10.7 127.8 115 25 17 77.8 130.2 152 162 16 5/8"

(1)Pressure max. recommended
Some flanges may equally well take metric bold and UNC bolts ; in this case reference numbers end with M/U or U/ISO, certain others can only take metric or UNC bolts ; in this case reference numbers end with M or U respectively.
* according to the ISO 6162-1 norm (bolts diameters are different)


FLANGES ACCORDING TO THE ISO 6162-2 / SAE 6000
Part N° PN bar1 DN F Ø D Ø J U Ø T GG Q FF O Bolts
Metric UNC
BM-6000-1/2"-M/U 400 13 7.2 32.5 24.6 16 8.7 18.2 40.5 48 56.5 8  
BM-6000-3/4"-M/U 400 19 8.2 42 32.5 19 10.5 23.8 50.8 60 71 10 5/16" 3/8"
BM-6000-1"-U 400 25 9 48.4 38.8 24 12 27.8 57.2 70 81 - 7/16"
BM-6000-1"-M 400 25 9 48.4 38.8 24 13 27.8 57.2 70 81 12 -
BM-6000-1"1/4-U / ISO* 400 32 9.8 54.8 44.5 27 13.5 31.8 66.6 78 95 12 1/2"
BM-6000-1"1/4/M 400 32 9.8 54.8 44.5 27 15 31.8 66.6 78 95 14 -
BM-6000-1"1/2-M/U 400 38 12 64.3 51.6 30 17 36.5 79.3 95 113 16 5/8"
BM-6000-2"-M / U / ISO 400 51 12 80.2 67.6 37 21 44.5 96.8 114 133 20 3/4"

(1)Pressure max. recommended
Some flanges may equally well take metric bold and UNC bolts ; in this case reference numbers end with M/U or U/ISO, certain others can only take metric or UNC bolts ; in this case reference numbers end with M or U respectively.
* according to the ISO 6162-1 norm (bolts diameters are different)
+ -

SPLIT FLANGES SAE 3000 / SAE 6000
DEMI BRIDE 994 raccord hydraulique
   
Click to collapse
DEMI BRIDES RECTANGULAIRES MONOBLOC
SPLIT FLANGES ACCORDING TO THE ISO 6162-1 / SAE 3000
Part N° PN bar1 DN F Ø D Ø J U Ø T GG/2 Q FF/2 O Bolts
Metric UNC
DB-3000-1/2"-M/U 350 13 6.2 31 24.3 13 8.7 8.75 38.1 22.8 54 8 5/16"
DB-3000-3/4"-M/U 350 19 6.2 38.9 32.2 14 10.5 11.15 47.6 25.9 65 10 3/8"
DB-3000-1"-M/U 315 25 7.5 45.3 38.5 16 10.5 13.1 52.4 29.2 70 10 3/8"
DB-3000-1"1/4-U 250 32 7.5 51.6 43.7 14 12 15.1 58.7 36.3 79.5 - 7/16"
DB-3000-1"1/4-M 250 32 7.5 51.6 43.7 14 12.5 15.1 58.7 36.3 79.5 12 -
DB-3000-1"1/4"/ISO* 250 32 7.5 51.6 43.7 14 10.5 15.1 58.7 36.3 79.5 10 -
DB-3000-1"1/2-U/ISO* 200 38 7.5 61.1 50.8 16 13.5 17.85 69.8 41.1 94 12 1/2"
DB-3000-1"1/2-M 200 38 7.5 61.1 50.8 16 14.5 17.85 69.8 41.1 94 14 -
DB-3000-2"-U/ISO* 200 51 9 72.3 62.8 16 13.5 21.45 77.8 48.2 102 12 1/2"
DB-3000-2"-M 200 51 9 72.3 62.8 16 14.5 21.45 77.8 48.2 102 14 -
DB-3000-2"1/2-U/ISO* 160 64 9 84.9 74.9 19 13.5 25.4 88.9 54.1 114.5 12 1/2"
DB-3000-2"1/2/M 160 64 9 84.9 74.9 19 14.5 25.4 88.9 51.4 114.5 14 -
DB-3000-3"-M/U 138 76 9 102.4 90.9 22 17 30.95 106.4 65.3 135 16 5/8"
DB-3000-3"1/2-M/U 35 89 10.7 115.1 102.4 22 17 34.95 120.7 69.6 152 16 5/8"
DB-3000-4"-M/U 35 102 10.7 127.8 115 25 17 38.9 130.2 75.9 162 16 5/8"

(1)Pressure max. recommended
Some flanges may equally well take metric bold and UNC bolts ; in this case reference numbers end with M/U or U/ISO, certain others can only take metric or UNC bolts ; in this case reference numbers end with M or U respectively.
* according to the ISO 6162-1 norm (bolts diameters are different)


SPLIT FLANGES ACCORDING TO THE ISO 6162-2 / SAE 6000
Part N° PN bar1 DN F Ø D Ø J U Ø T GG/2 Q FF/2 O Bolts
Metric UNC
DB-6000-1/2"-M/U 400 13 7.2 32.5 24.6 16 8.7 9.1 40.5 23.6 56.5 8 5/16"
DB-6000-3/4"-M/U 400 19 8.2 42 32.5 19 10.5 11.9 50.8 30 71 10 3/8"
DB-6000-1"-U 400 25 9 48.4 38.8 24 12 13.85 57.1 34.8 81 - 7/16"
DB-6000-1"-M 400 25 9 48.4 38.8 24 13 13.85 57.1 34.8 81 12 -
DB-6000-1"1/4-U / ISO* 400 32 9.8 54.8 44.5 27 13.5 15.85 66.7 38.6 95 12 1/2"
DB-6000-1"1/4-M 400 32 9.8 54.8 44.5 27 15 15.85 66.7 38.6 95 14 -
DB-6000-1"1/2-M/U 400 38 12 64.3 51.6 30 17 18.25 79.4 47.5 113 16 5/8"
DB-6000-2"-M / U / ISO 400 51 12 80.2 67.6 37 21 22.2 96.8 56.9 133 20 3/4"

(1)Pressure max. recommended
Some flanges may equally well take metric bold and UNC bolts ; in this case reference numbers end with M/U or U/ISO, certain others can only take metric or UNC bolts ; in this case reference numbers end with M or U respectively.
* according to the ISO 6162-1 norm (bolts diameters are different)

Port assembly

+ -

PORT ASSEMBLY FLANGES
SAE 3000 / SAE 6000
Click to collapse
BRIDES DE FIXATION BWI A PASSAGE INTEGRAL
PORT ASSEMBLY FLANGES BWI
S.A.E. 3000 / ISO 6162-1
Part N° PN bar1 DN For tube
Diameter to…at…		 Ø A Ø H1 L FF O GG Q Bolts
Metric UNC
BFX-3000-BWI-3/8 350 10 14-18 12 18 40 40 50 16.5 35 M 8X30  
BFX-3000-BWI-1/2 350 13 18-22 13 22 45 46 54 17.5 38.1 M 8X25 5/16-11/4
BFX-3000-BWI-3/4 350 19 25-28 19 28 50 52 65 22.3 47.6 M 10X30 3/8-11/4
BFX-3000-BWI-1 315 25 30-35 25 35 55 59 70 26.2 52.4 M 10X30 3/8-11/4
BFX-3000-BWI-11/4 * 250 32 38-43 32 43 60 73 79.5 30.2 58.7 M 12X30* 7/16-11/2
BFX-3000-BWI-11/2 * 210 38 48-50 38 50 65 83 94 35.7 69.8 M 14X35* 1/2-11/2
BFX-3000-BWI-2 * 51 60-63 47 61.8 70 97 102 42.9 77.8 M 14X35* 1/2-11/2
160
BFX-3000-BWI-21/2 * 160 64 73-76 58 74 75 109 114.5 50.8 88.9 M 14X40* 1/2-13/4
BFX-3000-BWI-3 138 76 88-90 70 90 85 131 135 61.9 106.4 M 16X50 5/8-13/4
BFX-3000-BWI-31/2 35 89 95-102 86 102 90 140 152 69.8 120.7 M 16X50 5/8-2
BFX-3000-BWI-4 35 102 113-120 96 114 100 152 162 77.8 130.2 M 16X50 5/8-2

(1)Pressure max. recommended
Flanges with 0'Ring and bolts.
*For metric bolts, add "M" after the reference ; for UNC bolts, add "U". Standard delivered with undivided split flanges, specify for split flanges.
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order


PORT ASSEMBLY FLANGES BWI
S.A.E. 6000 / ISO 6162-2
Part N° PN bar1 DN For tube
Diameter to…at…		 Ø A Ø H1 L FF O GG Q Bolts
Metric UNC
BFX-6000-BWI-1/2 400 13 20-22 13 22 45 48 56.5 18.2 40.5 M 8X30 5/16-11/4
BFX-6000-BWI-3/4 400 19 25-28 17.5 28 50 60 71 23.8 50.8 M 10X35 3/8-11/2
BFX-6000-BWI-1 400 25 30-35 22 35 55 70 81 27.8 57.2 M 12X45 7/16-13/4
BFX-6000-BWI-11/4* 400 32 38-43 29 43.8 60 78 95 31.8 66.6 M 14X50* 1/2-13/4
BFX-6000-BWI-11/2 400 38 48-52 35 50.6 65 95 113 36.5 79.3 M 16X55 5/8-21/4
BFX-6000-BWI-2 400 51 60-65 43 65 70 114 133 44.5 96.8 M 20X70 3/4-23/4

1)Pressure max. recommended
Flanges with 0'Ring and bolts.

*For metric bolts, add "M" after the reference ; for UNC bolts, add "U". Standard delivered with undivided split flanges, specify for split flanges.
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order
+ -

PORT ASSEMBLY FLANGES  REDUCING
SAE 3000 / SAE 6000
Click to collapse
BRIDES DE FIXATION BWR A PASSAGE REDUIT
PORT ASSEMBLY FLANGES BWR REDUCING
S.A.E. 3000 / ISO 6162-1
Part N° PN bar1 DN For tube
Diameter to…at…		 Ø A Ø H1 L FF O GG Q Bolts
Metric UNC
BFX-3000-BWR-1/2 350 13 16-18 12 18 45 46 54 17.5 38.1 M 8X25 5/16-11/4
BFX-3000-BWR-3/4 350 19 18-22 13 22 50 52 65 22.3 47.6 M 10X30 3/8-11/4
BFX-3000-BWR-1 315 25 25-28 19 28 55 59 70 26.2 52.4 M 10X30 3/8-11/4
BFX-3000-BWR-11/4 * 250 32 30-35 25 35 60 73 79.5 30.2 58.7 M 12X30* 7/16-11/2
BFX-3000-BWR-11/2 * 210 38 38-43 32 43 65 83 94 35.7 69.8 M 14X35* 1/2-11/2
BFX-3000-BWR-2 * 210 51 48-50 38 50 70 97 102 42.9 77.8 M 14X35* 1/2-11/2
BFX-3000-BWR-21/2 * 160 64 60-63 47 61.8 75 109 114.5 50.8 88.9 M 14X40* 1/2-13/4
BFX-3000-BWR-3 138 76 73-76 58 74 85 131 135 61.9 106.4 M 16X50 5/8-13/4
BFX-3000-BWR-31/2 35 89 88-90 70 90 90 140 152 69.8 120.7 M 16X50 5/8-2
BFX-3000-BWR-4 35 102 95-102 80 102 100 152 162 77.8 130.2 M 16X50 5/8-2

(1)Pressure max. recommended
Flanges with 0'Ring and bolts
For metric bolts, add "M" after the reference ; for UNC bolts, add "U". Standard delivered with undivided split flanges, specify for split flanges.
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order


PORT ASSEMBLY FLANGES BWR REDUCING
S.A.E. 6000 / ISO 6162-2
Part N° PN bar1 DN For tube
Diameter to…at…		 Ø A Ø H1 L FF O GG Q Bolts
Metric UNC
BFX-6000-BWR-1/2 400 13 16-18 11 17.5 45 48 56.5 18.2 40.5 M 8X30 5/16-11/4
BFX-6000-BWR-3/4 400 19 20-22 13 22 50 60 71 23.8 50.8 M 10X35 3/8-11/2
BFX-6000-BWR-1 400 25 25-28 17.5 28 55 70 81 27.8 57.2 M 12X45 7/16-13/4
BFX-6000-BWR-11/4* 400 32 30-35 22 35 60 78 95 31.8 66.6 M 14X50* 1/2-13/4
BFX-6000-BWR-11/2 400 38 38-43 29 43.8 65 95 113 36.5 79.3 M 16X55 5/8-21/4
BFX-6000-BWR-2 400 51 48-50 35 51 70 114 133 44.5 96.8 M 20X70 3/4-23/4

(1)Pressure max. recommended
Flanges with 0'Ring and bolts
For metric bolts, add "M" after the reference ; for UNC bolts, add "U". Standard delivered with undivided split flanges, specify for split flanges.
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order
+ -

PORT ASSEMBLY FLANGES INTEGRALE SOCKET WELD TUBE END
SAE 3000 / SAE 6000
Click to collapse
BRIDES DE FIXATION SOCKET WELDING A PASSAGE INTEGRAL
PORT ASSEMBLY FLANGES INTEGRALE SOCKET WELD TUBE END
S.A.E. 3000 / ISO 6162-1
Part N° PN bar1 DN Outer diameter tube Ø
L1		 Ø
L2		 ØA K L GG Q FF O Bolts
MM GAZ SCHD Metric UNC
BFX-3000-SWI-1/2"-20.5
BFX-3000-SWI-1/2"-21.7		 315 13 20 21.25 21.34 20.5
21.7		 30 13 13 60 17.5 38.1 46 54 M 8X25 5/16-1"1/4
BFX-3000-SWI-3/4"-25.5
BFX-3000-SWI-3/4"-27.3		 19 25 26.75 26.68 25.5
27.3		 35 19 13 68 22.3 47.6 52 65 M 10X30 3/8-1"1/4
BFX-3000-SWI-1"-30.5
BFX-3000-SWI-1"-32.5
BFX-3000-SWI-1"-34
BFX-3000-SWI-1"-35.5		 25 30
32
35		 33.50 33.40 30.5
32.5
34
35.5		 44 25 16 75 26.2 52.4 59 70 M 10X30 3/8-1"1/4
BFX-3000-SWI-1"1/4-38.5*
BFX-3000-SWI-1"1/4-40.5*
BFX-3000-SWI-1"1/4-43*		 200 32 38
40
42		 42.25 42.16 38.5
40.5
43		 55 32 18 95 30.2 58.7 73 79.5 M 12X30* 716-1"1/2
BFX-3000-SWI-1"1/2-49*
BFX-3000-SWI-1"1/2-50.4*		 38 50 48.25 48.26 49
50.4		 63 38 20 100 35.7 69.8 83 94 M 14X35* 1/2-1"1/2
BFX-3000-SWI-2"-61 *
BFX-3000-SWI-2"-65.8 *		 51 60
65		 60.30 60.32 61
65.8		 79 47 22 107 42.9 77.8 97 102 M 14X35* 1/2-1"1/2
BFX-3000-SWI-2"1/2-74*
BFX-3000-SWI-2"1/2-77*
BFX-3000-SWI-2"1/2-81*		 150 64 80 76.10 73.02 74
77
81		 98 58 24 130 50.8 88.9 109 114.5 M 14X40* 1/2-1"3/4
BFX-3000-SWI-3"-90.5 100 76 90   88.90 90.5 116 70 28 150 61.9 106.4 131 135 M 16X50 5/8-1"3/4

(1)Pressure max. recommended
Flanges with 0'Ring and bolts
For metric screws, add "M" after the reference ; for UNC screws, add "U".
SWI flanges head may only be fitted with split flanges (the shoulder does not allow a one piece fitting to pass through)
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order


PORT ASSEMBLY FLANGES INTEGRALE SOCKET WELD TUBE END
S.A.E. 6000 / ISO 6162-2
Part N° PN bar1 DN Outer diameter tube Ø
L1		 Ø
L2		 ØA K L GG Q FF O Bolts
MM GAZ SCHD Metric UNC
BFX-6000-SWI-1/2"-20.5
BFX-6000-SWI-1/2"-21.7
BFX-6000-SWI-1/2"-22.5		 380 13 20
22		 21.25 21.34 20.5
21.7
22.5		 32 13 13 60 18.2 40.5 48 56.5 M 8X30 5/16-1"1/4
BFX-6000-SWI-3/4"-25.7
BFX-6000-SWI-3/4"-27.3
BFX-6000-SWI-3/4"-28.7		 19 25
28		 26.75 26.68 25.7
27.3
28.7		 40 17.
5		 13 68 23.8 50.8 60 71 M 10X35 3/8-1"1/2
BFX-6000-SWI-1"-34
BFX-6000-SWI-1"-35.5		 25 35 33.5 33.4 34
35.5		 48 22 16 75 27.8 57.2 70 81 M 12X45 7/16-1"3/4

(1)Pressure max. recommended
Flanges with 0'Ring and bolts
For metric screws, add "M" after the reference ; for UNC screws, add "U".
SWI flanges head may only be fitted with split flanges (the shoulder does not allow a one piece fitting to pass through)
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order
+ -

PORT ASSAMBLY FLANGES INTEGRAL SOCKET WELD TUBE END
SAE 3000 / SAE 6000
Click to collapse
BRIDES DE FIXATION MONOBLOC SOCKET WELDING A PASSAGE INTEGRAL
PORT ASSAMBLY FLANGES INTEGRAL SOCKET WELD TUBE END
S.A.E. 3000 / ISO 6162-1
Part N° PN bar1 DN ØA ØB L GG Q FF O U K Bolts
Metric UNC
BFX-MONO-3000-SWI-1/2"-21.6 345 13 21.6 13 36 17.5 38.1 47 57 16 18 M 8X30 5/16"-1"1/4
BFX-MONO-3000-SWI-3/4"-27.2 19 27.2 19 36 22.3 47.6 49 66 18 18 M 10X35 3/8"-1"1/2
BFX-MONO-3000-SWI-1"-34 25 34.1 25 38 26.2 52.4 53 70 18 18 M 10X35 3/8"-1"1/2
BFX-MONO-3000-SWI-1"1/4-43 * 278 32 42.8 31 41 30.2 58.7 69 80 21 20 M 10X40 ou
M 12X40*		 7/16"-1"1/2
BFX-MONO-3000-SWI-1"1/2-49 * 210 38 48.6 38 44 35.7 69.8 77 94 25 22 M 12X45 ou
M 14X45*		 1/2"-1"3/4
BFX-MONO-3000-SWI-2"-61 * 51 61 50 45 42.9 77.8 89 103 25 24 M 12X45 ou
M 14X45*		 1/2"-1"3/4
BFX-MONO-3000-SWI-2"1/2-77 * 175 64 76.6 63 50 50.8 88.9 101 115 25 28 M 12X45 ou
M 14X45*		 1/2"-1"3/4
BFX-MONO-3000-SWI-3"-90.5 138 76 90.5 73 50 61.9 106.4 124 135 27 28 M 16X50 5/8"-2"

-DN 3"1/2 and 4" on request
(1)Pressure max. recommended
Flanges with 0'Ring and bolts
- Until 2" on request
For metric bolts, add "M" after the reference ; for UNC bolts, add "U".
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order


PORT ASSAMBLY FLANGES INTEGRAL SOCKET WELD TUBE END
S.A.E. 6000 / ISO 6162-2
Part N° PN bar1 DN ØA ØB L GG Q FF O U K Bolts
Metric UNC
BFX-MONO-6000-SWI-1/2"-21.6 400 1/2" 21.6 13 36 18.2 40.5 47 57 16 18 M 8X30 5/16"-1"1/4
BFX-MONO-6000-SWI-3/4"-27.2   3/4" 27.2 19 36 23.8 50.8 53 71 19 20 M 10X35 3/8"-1"1/2
BFX-MONO-6000-SWI-1"-34   1" 34.1 25 44 27.8 57.2 66 80 24 22 M 12X45 7/16"-1"3/4

(1)Pressure max. recommended
Flanges with 0'Ring and bolts
- Until 2" on request
For metric bolts, add "M" after the reference ; for UNC bolts, add "U".
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order
+ -

PORT ASSEMBLY FLANGES REDUCING SOCKET WELD TUBE END
SAE 3000 / SAE 6000
Click to collapse
BRIDES DE FIXATION BWR A PASSAGE REDUIT
PORT ASSEMBLY FLANGES REDUCING SOCKET WELD TUBE END
S.A.E. 3000 / ISO 6162-1
Part N° PN
bar1		 DN Outer diameter tube Ø
L1		 Ø
L2		 ØA K L GG Q FF O Bolts
MM GAZ SCHD Metric UNC
BFX-3000-SWR-1/2"-16.3
BFX-3000-SWR-1/2"-17.6		 315 13 16 16.75 17.14 16.3
17.6		 24 12 13 35 17.5 38.1 46 54 M 8X25 5/16-1"1/4
BFX-3000-SWR-3/4"-18.5
BFX-3000-SWR-3/4"-20.5
BFX-3000-SWR-3/4"-21.7		 19 18
20		 21.25 21.34 18.5
20.5
21.7		 31.5 13 13 40 22.3 47.6 52 65 M 10X30 3/8-1"1/4
BFX-3000-SWR-1"-25.5
BFX-3000-SWR-1"-27.3		 25 25 26.75 26.68 25.5
27.3		 38 19 13 45 26.2 52.4 59 70 M 10X30 3/8-1"1/4
BFX-3000-SWR-1"1/4-30.5 *
BFX-3000-SWR-1"1/4-32.5 *
BFX-3000-SWR-1"1/4-34 *
BFX-3000-SWR-1"1/4-35.5 *		 200 32 30
32
35		 33.50 33.40 30.5
32.5
34
35.5		 43 25 16 50 30.2 58.7 73 79.5 M 12X30* 7/16-1"1/2
BFX-3000-SWR-1"1/2-38.5 *
BFX-3000-SWR-1"1/2-40.5 *
BFX-3000-SWR-1"1/2-43 *		 38 38
40
42		 42.25 42.16 38.5
40.5
42.8		 50 32 18 55 35.7 69.8 83 94 M 14X35* 1/2-1"1/2
BFX-3000-SWR-2"-49 *
BFX-3000-SWR-2"-50.7 *		 51 50 48.25 48.26 49
50.7		 61.8 38 20 65 42.9 77.8 97 102 M 14X35* 1/2-1"1/2
BFX-3000-SWR-2"1/2-61 *
BFX-3000-SWR-2"1/2-65.8 *		 150 64 60
65		 60.30 60.30 61
65.8		 73.8 47 22 75 50.8 88.9 109 114.5 M 14X40* 1/2-1"3/4
BFX-3000-SWR-3"-74
BFX-3000-SWR-3"-77
BFX-3000-SWR-3"-81		 100 76 80 76.10 73.02 74
77
81		 90 58 25 85 61.9 106.4 131 135 M 16X50 5/8-1"3/4

(1)Pressure max. recommended
Flanges with 0'Ring and bolts
For metric bolts, add "M" after the reference
For UNC bolts, add "U".
Standard delivered with undivided split flanges, specify for split flanges.
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order


PORT ASSEMBLY FLANGES REDUCING SOCKET WELD TUBE END
S.A.E. 6000 / ISO 6162-2
Part N° PN
bar1		 DN Outer diameter tube Ø
L1		 Ø
L2		 ØA K L GG Q FF O Bolts
MM GAZ SCHD Metric UNC
BFX-6000-SWR-1/2-16.3
BFX-6000-SWR-1/2-17.6		 380 13 16 16.75 17.14 16.3
17.6		 24 11 13 35 18.2 40.5 48 56.5 M 8X30 5/16-1"1/4
BFX-6000-SWR-3/4-18.5
BFX-6000-SWR-3/4-20.5
BFX-6000-SWR-3/4-21.7		 19 18
20		 21.25 21.34 18.5
20.5
21.7		 32 13 13 40 23.8 50.8 60 71 M 10X35 3/8-1"1/2
BFX-6000-SWR-1"-25.5
BFX-6000-SWR-1"-27.3		 25 25 26.75 26.68 25.5
27.3		 38 17 13 45 27.8 57.2 70 81 M 12X45 7/16-1"3/4
BFX-6000-SWR-1"1/4-30.5*
BFX-6000-SWR-1"1/4-32.5*
BFX-6000-SWR-1"1/4-34*
BFX-6000-SWR-1"1/4-35.5*		 300 32 30
32
35		 33.50 33.40 30.5
32.5
34
35.5		 44.5 22 16 50 31.8 66.6 78 95 M 14X50* 1/2-1"3/4
BFX-6000-SWR-1"1/2-38.5
BFX-6000-SWR-1"1/2-40.5
BFX-6000-SWR-1"1/2-42.8		 38 38
40
42		 42.25 42.16 38.5
40.5
42.8		 51 29 18 55 36.5 79.3 95 113 M 16X55 5/8-2"1/4
BFX-6000-SWR-2"-49
BFX-6000-SWR-2"-50.8		 51 50 48.25 48.26 49
50.8		 67 35 20 65 44.5 96.8 114 133 M 20X70 3/4-2"3/4

(1)Pressure max. recommended
Flanges with 0'Ring and bolts
For metric bolts, add "M" after the reference
For UNC bolts, add "U".
Standard delivered with undivided split flanges, specify for split flanges.
+ -

PORT ASSEMBLY FLANGES WITH MALE BSP Co or NPT THREAD
SAE 3000 / SAE 6000
Click to collapse
BRIDES DE FIXATION A EMBOUTS FILETES GAZ CO ou NPT
PORT ASSEMBLY FLANGES WITH MALE BSP Co or NPT THREAD
S.A.E. 3000 / ISO 6162-1
Part N° PN Bar1 DN F Gaz co. Ø A L GG Q FF O P Bolts
Metric UNC
BFX-3000-F-G-CO-1/2"-A
BFX-3000-F-G-CO-1/2"-B		 300 13 1/2"
3/8"		 12
10		 50 17.5 38.1 46 54 19 M 8X25 5/16"-1"1/4
BFX-3000-F-G-CO-3/4"-A
BFX-3000-F-G-CO-3/4"-B		 19 3/4"
1/2"		 17
12		 55 22.3 47.6 52 65 27 M10X30 3/8"-1"1/4
BFX-3000-F-G-CO-1"-A
BFX-3000-F-G-CO-1"-B		 25 1"
3/4"		 22
17		 60 26.2 52.4 59 70 32 M10X30 3/8"-1"1/4
BFX-3000-F-G-CO-1"1/4-A *
BFX-3000-F-G-CO-1"1/4-B *		 150 32 1"1/4
1"		 27
22		 65 30.2 58.7 73 79.5 41 M12X30 * 7/16"-1"1/2
BFX-3000-F-G-CO-1"1/2-A *
BFX-3000-F-G-CO-1"1/2-B *		 38 1"1/2
1"1/4		 32
27		 70 35.7 69.8 83 94 46 M14X35 * 1/2"-1"1/2
BFX-3000-F-G-CO-2"-A *
BFX-3000-F-G-CO-2"-B *		 51 2"
1"1/2		 40
30		 75 42.9 77.8 97 102 55 M14X35 * 1/2"-1"1/2

(1)Pressure max. recommended
Flanges with 0'Ring and bolts
For metric bolts, add "M" after the reference ; for UNC bolts, add "U".
For threaded BSPP or NPT, replace G CO by G CYL or NPT into the reference
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order


PORT ASSEMBLY FLANGES WITH MALE BSP Co or NPT THREAD
S.A.E. 6000 / ISO 6162-2
Part N° PN Bar1 DN F Gaz co. Ø A L GG Q FF O P Bolts
Metric UNC
BFX-6000-F-G-CO-1/2"-A
BFX-6000-F-G-CO-1/2"-B		 350 13 1/2"
3/8"		 12
10		 50
50		 18.2 40.5 48 56 19 M 8X30 5/16"-1"1/4
BFX-6000-F-G-CO-3/4"-A
BFX-6000-F-G-CO-3/4"-B		 19 3/4"
1/2"		 17
12		 60
60		 23.8 50.8 60 71 26 M10X35 3/8"-1"1/2
BFX-6000-F-G-CO-1"-A
BFX-6000-F-G-CO-1"-B		 25 1"
3/4"		 22
17		 70
70		 27.7 57.1 70 81 32 M12X45 7/16"-1"3/4
BFX-6000-F-G-CO-1"1/4-A *
BFX-6000-F-G-CO-1"1/4-B *		 250 32 1"1/4
1"		 27
22		 75
75		 31.7 66.7 78 95 36 M14X50* 1/2"-1"3/4
BFX-6000-F-G-CO-1"1/2-A
BFX-6000-F-G-CO-1"1/2-B		 38 1"1/2
1"1/4		 32
27		 80
80		 36.5 79.4 95 113 41 M16X55 5/8"-2"1/4
BFX-6000-F-G-CO-2"-A
BFX-6000-F-G-CO-2"-B		 200 51 2"
1"1/2		 40
30		 90
90		 44.4 96.8 114 133 55 M20X70 3/4"-2"3/4

(1)Pressure max. recommended
Flanges with 0'Ring and bolts
For metric bolts, add "M" after the reference ; for UNC bolts, add "U".
For threaded BSPP or NPT, replace G CO by G CYL or NPT into the reference
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order
+ -

PORT ASSEMBLY FLANGES WITH MALE UNF-JIC 74° THREAD
SAE 3000 / SAE 6000
Click to collapse
BRIDES DE FIXATION FILETEES UNF MALE JIC
PORT ASSEMBLY FLANGES WITH MALE UNF-JIC 74° THREAD
S.A.E.3000 / ISO 6162-1
Part N° PN Bar1 DN Ø F UNF-2A Q GG FF2 O2 L U Bolts
Metric UNC
BFX-3000-F-JIC-1/2"-A
BFX-3000-F-JIC-1/2"-B
BFX-3000-F-JIC-1/2"-C		 250 13 3/4"-16
7/8"-14
1"1/16-12		 38.1 17.5 47 57 41
41
46		 16 M 8X30 5/16"-1"1/4
BFX-3000-F-JIC-3/4"-A
BFX-3000-F-JIC-3/4"-B
BFX-3000-F-JIC-3/4"-C		 19 7/8"-14
1"1/16-12
1"5/16-12		 47.6 22.3 49 66 47
49
50		 18 M 10X35 3/8"-1"1/2
BFX-3000-F-JIC-1"-A
BFX-3000-F-JIC-1"-B
BFX-3000-F-JIC-1"-C		 25
25		 1"1/16-12
1"5/16-12
1"5/8-12		 52.4 26.2 53 71 51
52
54		 18 M 10X35 3/8"-1"1/2
BFX-3000-F-JIC-1"1/4-A *
BFX-3000-F-JIC-1"1/4-B *
BFX-3000-F-JIC-1"1/4-C *		 32 1"5/16-12
1"5/8-12
1"7/8-12		 58.7 30.2 69 80 56
58
61		 21 M 10X40 *
ou
M 12X40		 7/16"-1"1/2
BFX-3000-F-JIC-1"1/2-A *
BFX-3000-F-JIC-1"1/2-B *		 210 38 1"5/8-12
1"7/8-12		 69.8 35.7 77 94 64
67		 24 M 12X45 *ou
M 14X45		 1/2"-1"3/4

(1)Pressure max. recommended
Flanges with 0'Ring and bolts
For metric bolts, add "M" after the reference ; for UNC bolts, add "U".
One piece flanges threaded from the block : on request made with threaded flanges head with JIC male and separate flange.
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order


PORT ASSEMBLY FLANGES WITH MALE UNF-JIC 74° THREAD
S.A.E. 6000 / ISO 6262-2
Part N° PN Bar1 DN Ø F UNF-2A Q GG FF2 O2 L U Bolts
Metric UNC
BFX-6000-F-JIC-1/2"-A
BFX-6000-F-JIC-1/2"-B
BFX-6000-F-JIC-1/2"-C		 350 13 3/4"-16
7/8"-14
1"1/16-12		 40.5 18.3 47 57 42
45
47		 16 M 8X30 5/16"-1"1/4
BFX-6000-F-JIC-3/4"-A
BFX-6000-F-JIC-3/4"-B
BFX-6000-F-JIC-3/4"-C		 19 7/8"-14
1"1/16-12
1"5/16-12		 50.8 23.8 53 71 49
51
52		 18 M 10X35 3/8"-1"1/2
BFX-6000-F-JIC-1"-A
BFX-6000-F-JIC-1"-B
BFX-6000-F-JIC-1"-C		 25 1"1/16-12
1"5/16-12
1"5/8-12		 57.1 27.8 69 80 58
59
61		 21 M 12X40 7/16"-1"3/4
250
BFX-6000-F-JIC-1"1/4-A *
BFX-6000-F-JIC-1"1/4-B *
BFX-6000-F-JIC-1"1/4-C *		 32 1"5/16-12
1"5/8-12
1"7/8-12		 66.7 31.6 77 94 64
66
69		 24 M 14X45 * 1/2"-1"3/4
BFX-6000-F-JIC-1"1/2-A
BFX-6000-F-JIC-1"1/2-B		 38 1"5/8-12
1"7/8-12		 79.4 36.7 89 106 70
73		 27 M 16X55 5/8"-2"1/4

(1)Pressure max. recommended
Flanges with 0'Ring and bolts
For metric bolts, add "M" after the reference ; for UNC bolts, add "U".
One piece flanges threaded from the block : on request made with threaded flanges head with JIC male and separate flange.
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order
+ -

PORT ASSEMBLY FLANGES FEMALE BSPP or NPT THREAD
SAE 3000 / SAE 6000
Click to collapse
BRIDES DE FIXATION TARAUDEES BSPP OU NPT
PORT ASSEMBLY FLANGES FEMALE BSPP or NPT THREAD
S.A.E. 3000 / ISO 6162-1
Part N° PN Bar1 DN Ø F L GG Q FF ØA K U O Bolts
BSPP Metric UNC
BFX-3000-T-BSP-1/2"
BFX-3000-T-BSP-1/2"-TAR-3/8"		 345 13 1/2"
3/8"		 36 17.5 38.1 47 13 15
13		 16 57 M 8X30 5/16'-1"1/4
BFX-3000-T-BSP-3/4" 19 3/4" 36 22.3 47.6 49 19 18 18 66 M 10X35 3/8"-1"1/2
BFX-3000-T-BSP-3/4"-TAR-1/2" 1/2" 13
BFX-3000-T-BSP-1"
BFX-3000-T-BSP-1"-TAR-3/4"		 25 1"
3/4"		 38 26.2 52.4 53 25
19		 20 18 71 M 10X35 3/8"-1"1/2
BFX-3000-T-BSP-1"1/4 * 278 32 1"1/4 41 30.2 58.7 69 31 22 21 80 M 10X40 ou 7/16"-1"1/2
BFX-3000-T-BSP-1"1/4-TAR-1" * 1" 25 M 12X40*
BFX-3000-T-BSP-1"1/2 *
BFX-3000-T-BSP-1"1/2-TAR-1"1/4 *		 210 38 1"1/2
1"1/4		 44 35.7 69.9 77 38
31		 24 25 94 M 12X45 ou
M 14X45*		 1/2"-1"3/4
BFX-3000-T-BSP-2" * 51 2" 45 42.9 77.8 89 50 26 25 103 M 12X45 ou 1/2"-1"3/4
BFX-3000-T-BSP-2"-TAR-1"1/2 * 1"1/2 38 M 14X45*
BFX-3000-T-BSP-2"1/2 *
BFX-3000-T-BSP-2"1/2-TAR-2" *		 175 64 2"1/2
2"		 50 50.8 88.9 101 63
50		 30 25 115 M 12X45 ou
M 14 X 45*		 1/2-1"3/4
BFX-3000-T-BSP-3" 138 76 3" 50 61.9 106.4 124 73 30 27 135 M 16X50 5/8"-2"
BFX-3000-T-BSP-3"-TAR-2"1/2 2"1/2 63
BFX-3000-T-BSP-3"1/2 35 89 3"1/2 50 69.8 120.7 136 89 30 27 152 M 16X50 5/8"-2"
BFX-3000-T-BSP-4" 35 102 4" 50 77.8 130.2 146 99 30 27 162 M 16X50 5/8"-2"

(1)Pressure max. recommended
Flanges with 0'Ring and bolts
For metric bolts, add "M" after the reference ; for UNC bolts, add "U".
For tapped NPT, replace BSP by NPT into the reference
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order


PORT ASSEMBLY FLANGES FEMALE BSPP or NPT THREAD
S.A.E. 6000 / ISO 6162-2
Part N° PN Bar1 DN Ø F L GG Q FF ØA K U O Bolts
BSP Metric UNC
BFX-6000-T-BSP-1/2"
BFX-6000-T-BSP-1/2"-TAR-3/8"		 400 13 1/2"
3/8		 36 18.2 40.5 47 14 15
13		 16 57 M 8X30 5/16"-1"1/4
BFX-6000-T-BSP-3/4" 19 3/4" 36 23.8 50.8 53 19 18 19 71 M 10X35 3/8"-1"1/2
BFX-6000-T-BSP-3/4"-TAR-1/2" 1/2" 14
BFX-6000-T-BSP-1"
BFX-6000-T-BSP-1"-TAR-3/4"		 25 1"
3/4"		 44 27.8 57.2 69 25
19		 20 24 80 M 12X45 7/16"-1"3/4
BFX-6000-T-BSP-1"1/4 * 32 1"1/4 44 31.6 66.6 77 31 22 27 94 M 14X50* 1/2"-1"3/4
BFX-6000-T-BSP-1"1/4-TAR-1" * 1" 25
BFX-6000-T-BSP-1"1/2
BFX-6000-T-BSP-1"1/2-TAR-1"1/4		 38 1"1/2
1"1/4		 51 36.5 79.3 89 38
31		 24 30 106 M 16X55 5/8"-2"1/4
BFX-6000-T-BSP-2" 51 2" 58 44.5 96.8 116 50 33 37 135 M 20X70 3/4"-2"1/2
(1)Pressure max. recommended
Flanges with 0'Ring and bolts
For metric bolts, add "M" after the reference ; for UNC bolts, add "U".
For tapped NPT, replace BSP by NPT into the reference
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order
+ -

PORT ASSEMBLY FLANGES FEMALE UN/UNF THREAD FOR O-RING
SAE 3000 / SAE 6000
Click to collapse
BRIDES DE FIXATION TARAUDEES DIN METRIQUES CYLINDRIQUES ETANCHEITE PAR JOINT ORING
PORT ASSEMBLY FLANGES FEMALE UN/UNF THREAD for O-ring
S.A.E. 3000 / ISO 6162-1
Part N° PN Bar1 DN Ø F
UN / UNF		 L GG Q FF ØA K U O Bolts
Metric UNC
BFX-3000-T-UNF-1/2"--A 345 13 3/4-16 36 17.5 38.1 47 13 17 16 57 M 8X30 5/16'-1"1/4
BFX-3000-T-UNF-3/4"-A 19 7/8"-14 36 22.3 47.6 49 19 17 18 66 M 10X35 3/8"-1"1/2
BFX-3000-T-UNF-3/4"-B   1"1/16-12           23        
BFX-3000-T-UNF-1"-A
BFX-3000-T-UNF-1"-B		 25 1"1/16-12
1"5/16-12		 38 26.2 52.4 53 25 23 18 71 M 10X35 3/8"-1"1/2
BFX-3000-T-UNF-1"1/4-A* 278 32 1"5/16-12 41 30.2 58.7 69 31 23 21 80 M 10X40 ou 7/16"-1"1/2
BFX-3000-T-UNF-1"1/4-B*   1"5/8-12                 M 12X40*  
BFX-3000-T-UNF-1"1/2-A*
BFX-3000-T-UNF-1"1/2-B*		 210 38 1"5/8-12
1"7/8-12		 44 35.7 69.8 77 38 23 25 94 M 12X45 ou
M 14X45*		 1/2"-1"3/4

(1)Pressure max. recommended
For metric bolts, add "M" after the reference ; for UNC bolts, add "U".
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order


PORT ASSEMBLY FLANGES FEMALE UN/UNF THREAD for O-ring
S.A.E. 6000 / ISO 6162-2
Part N° PN Bar1 DN Ø F
UN / UNF		 L GG Q FF ØA K U O Bolts
Metric UNC
BFX-6000-T-UNF-1/2-A 400 13 3/4"-16 36 18.3 40.5 47 13 17 16 57 M 8X30 5/16"-1"1/4
BFX-6000-T-UNF-3/4-A 19 7/8"-14 36 23.8 50.8 53 19 17 19 71 M 10X35 3/8"-1"1/2
BFX-6000-T-UNF-3/4-B   1"1/16-12           23        
BFX-6000-T-UNF-1"-A
BFX-6000-T-UNF-1"-B		 25 1"1/16-12
1"5/16-12		 44 27.8 57.1 69 25 23 24 80 M 12X45 7/16"-1"3/4
BFX-6000-T-UNF-1"1/4-A* 32 1"5/16-12 44 31.6 66.7 77 31 23 27 94 M 14X50 * 1/2"-1"3/4
BFX-6000-T-UNF-1"1/4-B*   1"5/8-12                    
BFX-6000-T-UNF-1"1/2-A
BFX-6000-T-UNF-1"1/2-B		 38 1"5/8-12
1"7/8-12		 51 36.7 79.4 89 38 23 30 106 M 16X55 5/8"-2"1/4

(1)Pressure max. recommended
For metric bolts, add "M" after the reference ; for UNC bolts, add "U".
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order
+ -

PORT ASSEMBLY FLANGES FEMALE METRIC THREAD for O-ring (ISO 6149-1)
SAE 3000 / SAE 6000
Click to collapse
BRIDES DE FIXATION TARAUDEES DIN METRIQUES CYLINDRIQUES ETANCHEITE PAR JOINT ORING
PORT ASSEMBLY FLANGES FEMALE METRIC THREAD for O-ring ( ISO 6149-1 )
S.A.E. 3000 / ISO 6162-1
Part N° PN Bar1 DN Ø F L GG Q FF ØA K U O Bolts
DIN Metric UNC
BFX-3000-T-DIN-1/2"-A
BFX-3000-T-DIN-1/2"-B		 345 13 18X1.5
20X1.5		 36 17.5 38.1 47 13 15 16 57 M 8X30 5/16'-1"1/4
BFX-3000-T-DIN-3/4"-A 19 22X1.5 36 22.3 47.6 49 19 16 18 66 M 10X35 3/8"-1"1/2
BFX-3000-T-DIN-3/4"-B 27X2 19
BFX-3000-T-DIN-1"-A
BFX-3000-T-DIN-1"-B		 25 27X2
33X2		 38 26.2 52.4 53 25 19 18 71 M 10X35 3/8"-1"1/2
BFX-3000-T-DIN-1"1/4-A* 278 32 33X2 41 30.2 58.7 69 31 19 21 80 M 10X40 ou 7/16"-1"1/2
BFX-3000-T-DIN-1"1/4-B* 42X2 20 M 12X40*
BFX-3000-T-DIN-1"1/2-A*
BFX-3000-T-DIN-1"1/2-B*		 210 38 42X2
48X2		 44 35.7 69.8 77 38 20
22		 25 94 M 12X45 ou
M 14X45*		 1/2"-1"3/4

(1)Pressure max. recommended
Flanges with 0'Ring and bolts
For metric bolts, add "M" after the reference ; for UNC bolts, add "U".
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order


PORT ASSEMBLY FLANGES FEMALE METRIC THREAD for O-ring ( ISO 6149-1 )
S.A.E. 6000 / ISO 6162-2
Part N° PN Bar1 DN Ø F L GG Q FF ØA K U O Bolts
DIN Metric UNC
BFX-6000-T-DIN-1/2-A
BFX-6000-T-DIN-1/2-B		 400 13 18X1.5
20X1.5		 36 18.2 40.5 47 13 15 16 57 M 8X30 5/16"-1"1/4
BFX-6000-T-DIN-3/4-A 19 22X1.5 36 23.8 50.8 53 19 16 19 71 M 10X35 3/8"-1"1/2
BFX-6000-T-DIN-3/4-B 27X2 19
BFX-6000-T-DIN-1"-A
BFX-6000-T-DIN-1"-B		 25 27X2
33X2		 44 27.8 57.2 69 25 19 24 80 M 12X45 7/16"-1"3/4
BFX-6000-T-DIN-1"1/4-A* 32 33X2 44 31.6 66.6 77 31 19 27 94 M 14X50 * 1/2"-1"3/4
BFX-6000-T-DIN-1"1/4-B* 42X2 20
BFX-6000-T-DIN-1"1/2-A
BFX-6000-T-DIN-1"1/2-B		 38 42X2
48X2		 51 36.5 79.3 89 38 20
22		 30 106 M 16X55 5/8"-2"1/4

(1)Pressure max. recommended
Flanges with 0'Ring and bolts
For metric bolts, add "M" after the reference ; for UNC bolts, add "U".
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order
+ -

UNION ASSEMBLY FLANGES BUTT WELD TUBE END (MONOBLOC)
SAE 3000 / SAE 6000
Click to collapse
BRIDES DE FIXATION MONOBLOC BWI
UNION ASSEMBLY FLANGES BUTT WELD TUBE END (MONOBLOC)
S.A.E. 3000 / ISO 6162-1
Part N° PN bar1 DN ØA ØB L GG Q FF O U Bolts
Metric UNC
BFX-MONO-3000-BWI-1/2" 345 13 21.6 13 36 17.5 38.1 47 57 16 M 8X30 5/16"-1"1/4
BFX-MONO-3000-BWI-3/4" 19 27.2 19 36 22.3 47.6 49 66 18 M 10X35 3/8"-1"1/2
BFX-MONO-3000-BWI-1" 315 25 34.5 25 38 26.2 52.4 53 71 18 M 10X35 3/8"-1"1/2
BFX-MONO-3000-BWI-1"1/4 250 32 42.8 31 41 30.2 58.7 69 80 21 M 10X40 ou
M 12X40*		 7/16"-1"1/2
BFX-MONO-3000-BWI-1"1/2 210 38 48.6 38 44 35.7 69.8 77 94 25 M 12X45 ou
M 14X45*		 1/2"-1"3/4
BFX-MONO-3000-BWI-2" 51 61 50 45 42.9 77.8 89 103 25 M 12X45 ou
M 14X45*		 1/2"-1"3/4
BFX-MONO-3000-BWI-2"1/2 160 64 76.6 63 50 50.8 88.9 101 115 25 M 12X45 ou
M 14X45*		 1/2"-1"3/4
BFX-MONO-3000-BWI-3" 138 76 89 73 50 61.9 106.4 124 135 27 M 16X50 5/8"-2"
BFX-MONO-3000-BWI-3"1/2 35 89 103 89 50 69.8 120.7 137 153 27 M 16X50 5/8"-2"
BFX-MONO-3000-BWI-4" 102 115 99 50 77.8 130.2 147 163 27 M 16X50 5/8"-2"
BFX-MONO-3000-BWI-5" 127 141 120 50 92 152.4 180 184 28 M 16X55 5/8"-2"1/4

(1)Pressure max. recommended
Flanges with 0'Ring and bolts
For metric bolts, add "M" after the reference ; for UNC bolts, add "U".
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order


UNION ASSEMBLY FLANGES BUTT WELD TUBE END (MONOBLOC)
S.A.E. 6000 / ISO 6162-2
Part N° PN bar1 DN ØA ØB L GG Q FF O U Bolts
Metric UNC
BFX-MONO-6000-BWR-1/2" 400 13 17.5 10 36 18.2 40.5 47 57 18 M 8X30 5/16"-1"1/4
BFX-MONO-6000-BWI-1/2" 13 21.6 13 36 18.2 40.5 47 57 18 M 8X30 5/16"-1"1/4
BFX-MONO-6000-BWI-3/4" 19 27.2 18 36 23.8 50.8 53 71 18 M 10X35 3/8"-1"1/2
BFX-MONO-6000-BWI-1" 25 34.5 22 44 27.8 57.2 66 80 24 M 12X45 7/16"-1"3/4
BFX-MONO-6000-BWI-1"1/4 * 32 42.8 28 44 31.8 66.6 77 94 25 M 14X50 * 1/2"-1"3/4
BFX-MONO-6000-BWI-1"1/2 38 48.6 32 51 36.5 79.3 89 106 29 M 16X55 5/8"-2"1/4
BFX-MONO-6000-BWI-2" 51 61 41 70 44.5 96.8 116 135 35 M 20X70 3/4"-2"1/2
BFX-MONO-6000-BWI-2"1/2 64 73.6 50 75 58.7 123.8 150 166 45 M 24X90 -
BFX-MONO-6000-BWI-3" 76 90 58 90 71.4 152.4 178 208 55 M 30X110 -

(1)Pressure max. recommended
Flanges with 0'Ring and bolts
For metric bolts, add "M" after the reference ; for UNC bolts, add "U".
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order
+ -

90° PORT ASSEMBLY FLANGES BUTT WELDING
SAE 3000 / SAE 6000
Click to collapse
BRIDES DE FIXATION RECTANGULAIRES BUTT WELDING COUDEES 90
90° PORT ASSEMBLY FLANGES BUTT WELDING
S.A.E. 3000 / ISO 6162-1
Part N° PN Bar1 DN ØH1 ØA C Q O GG FF M N L Bolts
Metric UNC
BFX-90°-3000-BWI-1/2" 350 13 21.6 13 12 38.1 57 17.5 63 17 18 13 M 8 5/16"
BFX-90°-3000-BWI-3/4" 19 27.2 19 12 47.6 68 22.3 66 18 22 15 M 10 3/8"
BFX-90°-3000-BWI-1" 315 25 34.5 25 13 52.4 74 26.2 77 19 28 15 M 10 3/8"
BFX-90°-3000-BWI-1"1/4* 250 32 42.8 31 13 58.7 81 30.2 91 22 30 17 M 10 ou
M 12*		 7/16"
BFX-90°-3000-BWI-1"1/2* 210 38 48.6 38 14 69.8 95 35.7 105 25 36 18 M 12 ou
M14*		 1/2"
BFX-90°-3000-BWI-2"* 51 61 50 15 77.8 105 42.9 110 25 41 18 M 12 ou
M 14*		 1/2"

on request 2"1/2
1)Pressure max. recommended
Flanges with 0'Ring and bolts
For metric bolts, add "M" after the reference ; for UNC bolts, add "U".
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order


90° PORT ASSEMBLY FLANGES BUTT WELDING
S.A.E. 6000 / ISO 6162-2
Part N° PN Bar1 DN ØH1 ØA C Q O GG FF M N L Bolts
Metric UNC
BFX-90°-6000-BWI-1/2" 400 13 21.6 13 12 40.5 57 18.2 63 17 18 13 M 8 5/16"
BFX-90°-6000-BWI-3/4" 19 27.2 18 12 50.8 72 23.8 77 20 28 15 M 10 3/8"
BFX-90°-6000-BWI-1" 25 34.5 22 13 57.2 82 27.8 91 24 26 19 M 12 7/16"
BFX-90°-6000-BWI-1"1/4* 32 42.8 28 13 66.6 95 31.8 105 25 36 21 M 14* 1/2"
BFX-90°-6000-BWI-1"1/2 38 48.6 32 15 79.3 110 36.5 109 26 41 25 M 16 5/8"
BFX-90°-6000-BWI-2" 51 61 41 15 96.8 134 44.5 133 35 45 32 M 20 3/4"
(1)Pressure max. recommended
Flanges with 0'Ring and bolts
For metric bolts, add "M" after the reference ; for UNC bolts, add "U".
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order
+ -

90° PORT ASSEMBLY FLANGES SOCKET WELDING
SAE 3000 / SAE 6000
Click to collapse
BRIDES DE FIXATION SOCKET WELDING COUDEES 90
90° PORT ASSEMBLY FLANGES SOCKET WELDING
S.A.E. 3000 / ISO 6162-1
Part N° PN Bar1 DN ØL1 ØA ØL2 K Q O GG FF M N L Bolts
Metric UNC
BFX-90°-3000-SWI-1/2"-21.6 315 13 21.6 13 34 5 38.1 57 17.5 51 17 18 13 M 8 5/16"
BFX-90°-3000-SWI-3/4"-27.2 19 27.2 19 38.5 5 47.6 68 22.3 50 18 22 15 M 10 3/8"
BFX-90°-3000-SWI-1"-34.5 25 34.1 25 44.5 6 52.4 72 26.2 55 19 28 15 M 10 3/8"
BFX-90°-3000-SWI-1"1/4-42.8 200 32 42.8 31 53.5 7 58.7 82 30.2 68 22 30 17 M 10 OU M 12* 7/16"
BFX-90°-3000-SWI-1"1/2-49 38 48.6 38 62.5 8 69.8 95 35.7 82 25 36 18 M 12 OU M 14* 1/2"
BFX-90°-3000-SWI-2"-61 51 61 50 77 10 77.8 105 42.9 94 25 41 18 M 12 OU M 14* 1/2"

on request 2"1/2
(1)Pressure max. recommended
Flanges with 0'Ring and bolts
For metric bolts, add "M" after the reference ; for UNC bolts, add "U".
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order


90° PORT ASSEMBLY FLANGES SOCKET WELDING
S.A.E. 6000 / ISO 6162-2
Part N° PN Bar1 DN ØL1 ØA ØL2 K Q O GG FF M N L Bolts
Metric UNC
BFX-90°-6000-SWI-1/2"-21.6 400 13 21.6 13 34 5 40.5 57 18.2 51 17 18 13 M 8 5/16"
BFX-90°-6000-SWI-3/4"-27.2 19 27.2 19 44.5 6 50.8 68 23.8 50 18 22 15 M 10 3/8"
BFX-90°-6000-SWI-1"-34.1 25 34.1 25 53.5 7 57.2 72 27.8 55 19 28 15 M 12 7/16"

(1)Pressure max. recommended
Flanges with 0'Ring and bolts
For metric bolts, add "M" after the reference ; for UNC bolts, add "U".
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order
+ -

90° PORT ASSEMBLY FLANGES FEMALE THREADED BSP
SAE 3000 / SAE 6000
Click to collapse
BRIDES DE FIXATION TARAUDEES GAZ OU NPT COUDEES 90
90° PORT ASSEMBLY FLANGES FEMALE THREADED BSP
S.A.E. 3000 / ISO 6162-1
Part N° PN Bar1 DN ØF ØA M N L Ø H K O Q FF GG Bolts
Metric UNC
BFX-90°-3000-T-BSP-1/2" 345 13 1/2" 13 17 18 13 34 19 57 38.1 59 17.5 M 8 5/16"
BFX-90°-3000-T-BSP-3/4" 19 3/4" 19 18 22 15 38.5 19 68 47.6 63 22.3 M 10 3/8"
BFX-90°-3000-T-BSP-1" 25 1" 25 19 28 15 44.5 19 74 52.4 68 26.2 M 10 3/8"
BFX-90°-3000-T-BSP-1"1/4* 278 32 1"1/4 31 22 30 17 53.5 22 81 58.7 84 30.2 M 10 ou
M 12*		 7/16"
BFX-90°-3000-T-BSP-1"1/2* 210 38 1"1/2 38 25 36 18 62.5 24 95 69.8 97 35.7 M 12 ou
M 14*		 1/2"
BFX-90°-3000-T-BSP-2"* 51 2" 50 25 41 18 77 26 105 77.8 109 42.9 M 12 ou
M 14*		 1/2"

(1)Pressure max. recommended
Flanges with 0'Ring and bolts
For threaded NPT, replace G CO by NPT into the reference
Protection : Yellow galvanized
For metric bolts, add "M" after the reference ; for UNC bolts, add "U".
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order


90° PORT ASSEMBLY FLANGES FEMALE THREADED BSP
S.A.E. 6000 / ISO 6162-2
Part N° PN Bar1 DN ØF ØA M N L Ø H K O Q FF GG Bolts
Metric UNC
BFX-90°-6000-T-BSP-1/2" 400 13 1/2" 13 17 18 13 34 19 57 40.5 59 18.2 M 8 5/16"
BFX-90°-6000-T-BSP-3/4" 19 3/4" 19 20 28 15 44.5 19 68 50.8 68 23.8 M 10 3/8"
BFX-90°-6000-T-BSP-1" 25 1" 25 24 30 19 53.5 19 74 57.2 84 27.8 M 12 7/16"
BFX-90°-6000-T-BSP-1"1/4* 32 1"1/4 31 25 36 21 62.5 22 81 66.6 97 31.8 M 14 * 1/2"
BFX-90°-6000-T-BSP-1"1/2 38 1"1/2 38 26 41 25 77 24 95 79.3 109 36.5 M 16 5/8"
BFX-90°-6000-T-BSP-2" 51 2" 50 35 45 32 87 26 105 96.8 133 44.4 M 20 3/4"

(1)Pressure max. recommended
Flanges with 0'Ring and bolts
For threaded NPT, replace G CO by NPT into the reference
Protection : Yellow galvanized
For metric bolts, add "M" after the reference ; for UNC bolts, add "U".
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order
+ -

90° PORT ASSEMBLY FLANGES MALE 24° CONE END DIN 2353 (ISO 8434-1)
SAE 3000 / SAE 6000
Click to collapse
BRIDES DE FIXATION 90 FILETEES METRIQUES A CONE INTERIEUR 24 NORME DIN 2353
90° PORT ASSEMBLY FLANGES MALE 24° CONE END DIN 2353 ( ISO 8434-1 )
S.A.E. 3000 / ISO 6162-1
Part N° PN
bar1		 DN Ø F Ø D Ø A Q GG G H I L Bolts
Metric UNC
BFX-90°-3000-F-DIN-1/2"-A
BFX-90°-3000-F-DIN-1/2"-B
BFX-90°-3000-F-DIN-1/2"-C		 315 13 20X1.5
22X1.5
24X1.5		 12 S
15 L
16 S		 8
11
12		 38.1 17.5 36 16 18 14 M 8 5/16"
350
BFX-90°-3000-F-DIN-3/4"-A   24X1.5 16 S 12                
BFX-90°-3000-F-DIN-3/4"-B 19 30X2.0 20 S 16 47.6 22.3 38 18 22 14 M 10 3/8"
BFX-90°-3000-F-DIN-3/4"-C 160   30X2.0 22 L 18                
BFX-90°-3000-F-DIN-1"-A
BFX-90°-3000-F-DIN-1"-B
BFX-90°-3000-F-DIN-1"-C		 315 25 30X2.0
36X2.0
36X2.0		 20 S
25 S
28 L		 16
20
23		 52.4 26.2 42 19 28 14 M 10 3/8"
160
BFX-90°-3000-F-DIN1"1/4-A* 250   36X2.0 25 S 20             M10  
BFX-90°-3000-F-DIN-1"1/4-B* 32 42X2.0 30 S 25 58.7 30.2 50 22 30 18 ou 7/16"
BFX-90°-3000-F-DIN-1"1/4-C* 160    45X2.0 35 L 30             M 12*  
BFX-90°-3000-F-DIN-1"1/2-A*
BFX-90°-3000-F-DIN-1"1/2-B*
BFX-90°-3000-F-DIN-1"1/2-C*		 38 45X2.0
52X2.0
52X2.0		 35 L
38 S
42 L		 30
32
36		 69.8 35.7 58 25 36 18 M 12
ou
M 14*		 1/2"
200
160

(1)Pressure max. recommended
Flanges with 0'Ring and bolts
Protection : Yellow galvanized
For metric bolts, add "M" after the reference ; for UNC bolts, . add "U".
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order


90° PORT ASSEMBLY FLANGES MALE 24° CONE END DIN 2353 ( ISO 8434-1 )
S.A.E. 6000 / ISO 6162-2
Part N° PN
bar1		 DN Ø F Ø D Ø A Q GG G H I L Bolts
Metric UNC
BFX-90°-6000-F-DIN-1/2"-A
BFX-90°-6000-F-DIN-1/2"-B
BFX-90°-6000-F-DIN-1/2"-C		 400 13 20X1.5
22X1.5
24X1.5		 12 S
14 S
16 S		 8
10
12		 40.5 18.2 36 16 20 14 M 8 5/16"
BFX-90°-6000-F-DIN-3/4"-A   24X1.5 16 S 12                
BFX-90°-6000-F-DIN-3/4"-B 19 30X2.0 20 S 20 50.8 23.8 41 19 26 14 M 10 3/8"
BFX-90°-6000-F-DIN-3/4"-C 160   30X2.0 22 L 23                
BFX-90°-6000-F-DIN-1"-A
BFX-90°-6000-F-DIN-1"-B
BFX-90°-6000-F-DIN-1"-C		 400 25 30X2.0
36X2.0
36X2.0		 20 S
25 S
28 L		 16
20
23		 57.2 27.8 50 24 30 14 M 12 7/16"
160
BFX-90°-6000-F-DIN-1"1/4-A* 400   36X2.0 25 S 20                
BFX-90°-6000-F-DIN-1"1/4-B* 32 42X2.0 30 S 25 66.6 31.8 58 25 36 18 M 14 * 1/2"
BFX-90°-6000-F-DIN-1"1/4-C* 160   45X2.0 35 L 30                
BFX-90°-6000-F-DIN-1"1/2-A
BFX-90°-6000-F-DIN-1"1/2-B
BFX-90°-6000-F-DIN-1"1/2-C		 400 38 42X2.0
52X2.0
52X2.0		 30 S
38 S
42 L		 25
32
36		 79.3 36.5 65 26 41 18 M 16 5/8"
160

(1)Pressure max. recommended
Flanges with 0'Ring and bolts
Protection : Yellow galvanized
For metric bolts, add "M" after the reference ; for UNC bolts, . add "U".
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order
+ -

90° PORT ASSEMBLY FLANGES MALE BSPP CONE END (60°)
SAE 3000 / SAE 6000
Click to collapse
BRIDES DE FIXATION FILETEES MALE BSP COUDEES 90
90° PORT ASSEMBLY FLANGES MALE BSPP CONE END ( 60°)
S.A.E. 3000 / ISO 6162-1
Part N° PN Bar1 DN Ø F BSPP Q GG D E M L Bolts
Metric UNC
BFX-90°-3000-F-MBSP-1/2"-A
BFX-90°-3000-F-MBSP-1/2"-B
BFX-90°-3000-F-MBSP-1/2"-C		 345 13 3/8"
1/2"
3/4"		 38.1 17.5 17
17
20		 37
39
40		 16 14 M 8 5/16"
BFX-90°-3000-F-MBSP-3/4"-A   1/2"     20 41        
BFX-90°-3000-F-MBSP-3/4"-B 19 3/4" 47.6 22.3 20 44 18 14 M 10 3/8"
BFX-90°-3000-F-MBSP-3/4"-C   1"     25 45        
BFX-90°-3000-F-MBSP-1"-A
BFX-90°-3000-F-MBSP-1"-B
BFX-90°-3000-F-MBSP-1"-C		 25 3/4"
1"
1"1/4		 52.4 26.2 20
25
31		 47
48
49		 19 14 M 10 3/8"
BFX-90°-3000-F-MBSP-1"1/4-A* 278   1"     25 54     M 10  
BFX-90°-3000-F-MBSP-1"1/4-B* 32 1"1/4 58.7 30.2 31 55 22 18 ou 7/16"
BFX-90°-3000-F-MBSP-1"1/4-C*   1"1/2     37 56     M 12*  
BFX-90°-3000-F-MBSP-1"1/2-A*
BFX-90°-3000-F-MBSP-1"1/2-B*		 210 38 1"1/4
1"1/2		 69.8 35.7 31
37		 59
61		 25 18 M 12 ou
M 14*		 1/2"

(1)Pressure max. recommended
Flanges with 0'Ring and bolts
Protection : Yellow galvanized
Sealing on 60° cone in front of threading
For metric bolts, add "M" after the reference ; for UNC bolts, add "U".
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order


90° PORT ASSEMBLY FLANGES MALE BSPP CONE END ( 60°)
S.A.E. 6000 / ISO 6162-2
Part N° PN
bar1		 DN Ø F BSPP Q GG D E M L Bolts
Metric UNC
BFX-90°-6000-F-MBSP-1/2"-A
BFX-90°-6000-F-MBSP-1/2"-B
BFX-90°-6000-F-MBSP-1/2"-C		 400 13 3/8"
1/2"
3/4"		 40.5 18.2 17
17
20		 37
39
40		 16 14 M 8 5/16"
BFX-90°-6000-F-MBSP-3/4"-A   1/2"     20 45        
BFX-90°-6000-F-MBSP-3/4"-B 19 3/4" 50.8 23.8 20 48 19 14 M 10 3/8"
BFX-90°-6000-F-MBSP-3/4"-C   1"     25 50        
BFX-90°-6000-F-MBSP-1"-A
BFX-90°-6000-F-MBSP-1"-B
BFX-90°-6000-F-MBSP-1"-C		 25 3/4"
1"
1"1/4		 57.2 27.8 25
25
31		 52
54
55		 24 18 M 12 7/16"
BFX-90°-6000-F-MBSP-1"1/4-A*   1"     31 59        
BFX-90°-6000-F-MBSP-1"1/4-B* 32 1"1/4 66.6 31.8 31 59 25 18 M 14* 1/2"
BFX-90°-6000-F-MBSP-1"1/4-C*   1"1/2     37 61        
BFX-90°-6000-F-MBSP-1"1/2-A
BFX-90°-6000-F-MBSP-1"1/2-B		 38 1"1/4
1"1/2		 79.3 36.5 37
37		 64
66		 26 20 M 16 5/8"

(1)Pressure max. recommended
Flanges with 0'Ring and bolts
Protection : Yellow galvanized
Sealing on 60° cone in front of threading
For metric bolts, add "M" after the reference ; for UNC bolts, add "U".
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order
+ -

90° PORT ASSEMBLY FLANGES MALE UNF THREAD (JIC 74°)
SAE 3000 / SAE 6000
Click to collapse
BRIDES DE FIXATION FILETEES MALE JIC COUDEES 90
90° PORT ASSEMBLY FLANGES MALE UNF THREAD (JIC 74°)
S.A.E. 3000 / ISO 6162-1
Part N° PN
bar1		 DN Ø F Q GG D E H L Bolts
Metric UNC
BFX-90°-3000-F-JIC-1/2"-A
BFX-90°-3000-F-JIC-1/2"-B
BFX-90°-3000-F-JIC-1/2"-C		 250 13 3/4"-16
7/8"-14
1"1/16-12		 38,1 17.5 17
17
20		 40
42
43		 16 14 M 8 5/16"
BFX-90°-3000-F-JIC-3/4"-A
BFX-90°-3000-F-JIC-3/4"-B
BFX-90°-3000-F-JIC-3/4"-C		 19 7/8"-14
1"1/16-12
1"5/16-12		 47.6 22.3 20
20
25		 45
47
48		 18 14 M 10 3/8"
BFX-90°-3000-F-JIC-1"-A
BFX-90°-3000-F-JIC-1"-B		 25 1"1/16-12
1"5/16-12		 52.4 26.2 20
25		 50
51		 19 15 M 10 3/8"
BFX-90°-3000-F-JIC-1"1/4-A*
BFX-90°-3000-F-JIC-1"1/4-B*
BFX-90°-3000-F-JIC-1"1/4-C*		 32 1"5/16-12
1"5/8-12
1"7/8-12		 58.7 30.2 25
31
37		 56
58
61		 22 18 M 10 ou
M 12*		 7/16"
BFX-90°-3000-F-JIC-1"1/2-A*
BFX-90°-3000-F-JIC-1"1/2-B*		 210 38 1"5/8-12
1"7/8-12		 69.8 35.7 31
37		 63
66		 25 20 M 12 ou
M 14*		 1/2"

(1)Pressure max. recommended
Flanges with 0'Ring and bolts
Protection : Yellow galvanized
For metric bolts, add "M" after the reference ; for UNC bolts, add "U".
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order


90° PORT ASSEMBLY FLANGES MALE UNF THREAD (JIC 74°)
S.A.E. 6000 –/ ISO 6162-2
Part N° PN
bar1		 DN Ø F Q GG D E H L Bolts
Metric UNC
BFX-90°-6000-F-JIC-1/2"-A
BFX-90°-6000-F-JIC-1/2"-B
BFX-90°-6000-F-JIC-1/2"-C		 350 13 3/4"-16
7/8"-14
1"1/16-12		 40.5 18.2 17
17
20		 40
42
43		 16 14 M 8 5/16"
BFX-90°-6000-F-JIC-3/4"-A
BFX-90°-6000-F-JIC-3/4"-B
BFX-90°-6000-F-JIC-3/4"-C		 19 7/8"-14
1"1/16-12
1"5/16-12		 50.8 23.8 20
20
25		 49
51
52		 19 14 M 10 3/8"
BFX-90°-6000-F-JIC-1"-A
BFX-90°-6000-F-JIC-1"-B
BFX-90°-6000-F-JIC-1"-C		 25 1"1/16-12
1"5/16-12
1"5/8-12		 57.2 27.8 25
25
31		 55
56
58		 24 18 M 12 7/16"
250
BFX-90°-6000-F-JIC-1"1/4-A*
BFX-90°-6000-F-JIC-1"1/4-B*
BFX-90°-6000-F-JIC-1"1/4-C*		 32 1"5/16-12
1"5/8-12
1"7/8-12		 66.6 31.8 31
31
37		 56
63
63		 25 18 M 14 * 1/2"
BFX-90°-6000-F-JIC-1"1/2-A
BFX-90°-6000-F-JIC-1"1/2-B		 38 1"5/8-12
1"7/8-12		 79.3 36.5 37
37		 67
70		 26 20 M 16 5/8"

(1)Pressure max. recommended
Flanges with 0'Ring and bolts
Protection : Yellow galvanized
For metric bolts, add "M" after the reference ; for UNC bolts, add "U".
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

Test port square

BRIDES PRISES DE PRESSION SAE ISO 6162 1 et 2
TEST PORT SQUARE FLANGES
S.A.E. 3000 – ISO 6162-1
Part N° PN bar1 DN Ø A L GG Q FF O Ø V
BM-3000-PRISE-TEST-XX-3/8"-M
BM-3000-PRISE-TEST-XX-1/2"-M/U		 350 10
13		 12
13		 22
25		 16.5
17.5		 35
38.1		 40
45		 50
54		 9
9
BM-3000-PRISE-TEST-XX-3/4"-M/U 19 19 30 22.3 47.6 50 65 11
BM-3000-PRISE-TEST-XX-1"-M/U
BM-3000-PRISE-TEST-XX-1"1/4 M ISO ou M/U*		 315 25
32		 25
32		 30
35		 26.2
30.2		 52.4
58.7		 60
75		 70
80		 11
11 ou 13
250
BM-3000-PRISE-TEST-XX-1"1/2 M ou U/ISO* 210 38 38 35 35.7 69.8 80 94 13.5 ou 15
BM-3000-PRISE-TEST-XX-2" M ou U/ISO*
BM-3000-PRISE-TEST-XX-2"1/2 M ou U/ISO*		 51
64		 47
58		 40
40		 42.9
50.8		 77.8
88.9		 100
110		 102
114		 13.5 ou 15
13.5 ou 15
160
BM-3000-PRISE-TEST-XX-3" M/U 138 76 70 45 61.9 106.4 130 135 17

(1)Pressure max. recommended
These flange bodies are fitted with pressure inlets with M 10X100 A shape sealed layout - G 1/4 on request - Galvanized-bichromated.


TEST PORT SQUARE FLANGES
S.A.E. 6000 – ISO 6162-2
Part N° PN bar1 DN Ø A L GG Q FF O Ø V
BM-6000-PRISE-TEST-XX-1/2-M/U
BM-6000-PRISE-TEST-XX-3/4"-M/U		 400 13
19		 13
17.5		 25
30		 18.2
23.8		 40.5
50.8		 48
60		 56
71		 9
11
BM-6000-PRISE-TEST-XX-1"-M/U 25 22 30 27.8 57.2 70 81 12.5
BM-6000-PRISE-TEST-XX-1"1/4-M ou U/ISO*
BM-6000-PRISE-TEST-XX-1"1/2-M/U		 32
38		 29
35		 35
35		 31.8
36.5		 66.6
79.3		 78
95		 95
113		 13.5 ou 15
17
BM-6000-PRISE-TEST-XX-2" M/ U/ISO 51 43 40 44.5 96.8 114 133 21

(1)Pressure max. recommended
These flange bodies are fitted with pressure inlets with M 10X100 A shape sealed layout - G 1/4 on request - Galvanized-bichromated.

Union assembly

+ -

UNION ASSEMBLY FLANGES BUTT WELDING
SAE 3000 / SAE 6000
Click to collapse
BRIDES DE LIAISON BUTT WELDING A PASSAGE INTEGRAL
UNION ASSEMBLY FLANGES BUTT WELDING
S.A.E. 3000 – ISO 6162-1
Part N° PN bar1 DN For tube
diameter to... at ...		 Ø A Ø H1 L FF O GG Q Bolts
Metric
BL-3000-BWI-3/8" **
BL-3000-BWI-1/2"		 350 10
13		 14 -18
18 -22		 12
13		 18
22		 80
90		 40
46		 50
54		 16.5
17.5		 35
38.1		 M 8X45
M 8X40
BL-3000-BWI-3/4" 19 25 - 28 19 28 100 52 65 22.3 47.6 M 10X40
BL-3000-BWI-1"
BL-3000-BWI-1"1/4 *		 315 25
32		 30 - 35
38 - 43		 25
32		 35
43		 110
120		 59
73		 70
79.5		 26.2
30.2		 52.4
58.7		 M 10X45
M 12X45*
250
BL-3000-BWI-1"1/2 * 210 38 48 - 50 38 50 130 83 94 35.7 69.8 M 14X50 *
BL-3000-BWI-2" *
BL-3000-BWI-2"1/2 *		 51
64		 60 - 63
73 - 76		 47
58		 61.8
74		 140
150		 97
109		 102
114.5		 42.9
50.8		 77.8
88.9		 M 14X50 *
M 14X55 *
160
BL-3000-BWI-3" 138 76 88 - 90 70 90 170 131 135 61.9 106.4 M 16X65
BL-3000-BWI-3"1/2
BL-3000-BWI-4"		 35 89
102		 95 - 102
113 - 120		 86
96		 102
114		 180
200		 140
152		 152
162		 69.8
77.8		 120.7
130.2		 M 16X65
M 16X70

(1)Pressure max. recommended
Flanges with 0'Ring and metric bolds.
** In 3/8" undivided split flanges in drawn steel not wrought
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order.


UNION ASSEMBLY FLANGES BUTT WELDING
S.A.E. 6000 – ISO 6162-2
Part N° PN bar1 DN For tube
diameter to... at ...		 Ø A Ø H1 L FF O GG Q Bolts
Metric
BL-6000-BWI-1/2"
BL-6000-BWI-3/4"		 400 13
19		 20 - 22
25 - 28		 13
17.5		 22
28		 90
100		 48
60		 56.5
71		 18.2
23.8		 40.5
50.8		 M 8X45
M 10X50
BL-6000-BWI-1" 25 30 - 35 22 35 110 70 81 27.8 57.2 M 12X65
BL-6000-BWI-1"1/4 *
BL-6000-BWI-1"1/2		 32
38		 38 - 43
48 - 52		 29
35		 43.8
50.6		 120
130		 78
95		 95
113		 31.8
36.5		 66.6
79.3		 M 14X70 *
M 16X80
BL-6000-BWI-2" 51 60 - 65 43 65 140 114 133 44.5 96.8 M 20X100

(1)Pressure max. recommended
Flanges with 0'Ring and metric bolds.
** In 3/8" undivided split flanges in drawn steel not wrought
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order.
+ -

UNION ASSEMBLY FLANGES BUTT WELDING REDUCING
SAE 3000 / SAE 6000
Click to collapse
BRIDES DE LIAISON BUTT WELDING A PASSAGE REDUIT
UNION ASSEMBLY FLANGES BUTT WELDING REDUCING
S.A.E. 3000 – ISO 6162-1
Part N° PN bar1 DN For tube
diameter to... at ...		 ØA ØH1 L FF O GG Q Bolts
Metric
BL-3000-BWR-1/2"
BL-3000-BWR-3/4"		 350 13
19		 14 - 18
18 - 22		 12
13		 18
22		 90
100		 46
52		 54
65		 17.5
22.3		 38.1
47.6		 M 8X40
M 10X40
BL-3000-BWR-1" 315 25 25 - 28 19 28 110 59 70 26.2 52.4 M 10X45
BL-3000-BWR-1"1/4 *
BL-3000-BWR-1"1/2 *		 250 32
38		 30 - 35
38 - 43		 25
32		 35
43		 120
130		 73
83		 79.5
94		 30.2
35.7		 58.7
69.8		 M 12X45 *
M 14X50 *
210
BL-3000-BWR-2" * 51 48 - 50 38 50 140 97 102 42.9 77.8 M 14X50 *
BL-3000-BWR-2"1/ 2 *
BL-3000-BWR-3"		 160 64
76		 60 - 63
73 - 76		 47
58		 61.8
76		 150
170		 109
131		 114.5
135		 50.8
61.9		 88.9
106.4		 M 14X55 *
M 16X65
138
BL-3000-BWR-3"1/2 35 89 88 - 90 70 90 180 140 152 69.8 120.7 M 16X65
BL-3000-BWR-4" 102 95 - 102 80 102 200 152 162 77.8 130.2 M 16X70

(1)Pressure max. recommended
Union assembly flanges can only be delivered with undivided split flanges
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order.


UNION ASSEMBLY FLANGES BUTT WELDING REDUCING
S.A.E. 6000 – ISO 6162-2
Part N° PN bar1 DN For tube
diameter to... at ...		 ØA ØH1 L FF O GG Q Bolts
Metric
BL-6000-BWR-1/2"
BL-6000-BWR-3/4"		 400 13
19		 16 - 18
20 - 22		 11
13		 17.5
22		 90
100		 48
60		 56.5
71		 18.2
23.8		 40.5
50.8		 M 8X45
M 10X50
BL-6000-BWR-1" 25 25 - 28 17.5 28 110 70 81 27.8 57.2 M 12X65
BL-6000-BWR-1"1/4 *
BL-6000-BWR-1"1/2		 32
38		 30 - 35
38 -43		 22
29		 35
43.8		 120
130		 78
95		 95
113		 31.8
36.5		 66.6
79.3		 M 14X70 *
M 16X80
BL-6000-BWR-2" 51 48 - 52 35 51 140 114 133 44.5 96.8 M 20X100

(1)Pressure max. recommended
Union assembly flanges can only be delivered with undivided split flanges
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order.
+ -

UNION ASSEMBLY FLANGES REDUCING SOCKET WELDING
SAE 3000 / SAE 6000
Click to collapse
BRIDES DE LIAISON SOCKET WELDING A PASSAGE REDUIT
UNION ASSEMBLY FLANGES REDUCING SOCKET WELDING
S.A.E. 3000 – ISO 6162-1
Part N° PN Bar1 DN Outer diameter tube ØL1 ØL2 ØA K L GG Q FF O Bolts
Metric
MM GAZ SCHD
BL-3000-SWR-1/2"-16.5
BL-3000-SWR-1/2"-17.6		 315 13 16 16,75 17.14 16.5
17.6		 24 12 12 70 17.5 38.1 46 54 M 8X40
BL-3000-SWR-3/4"-18.5
BL-3000-SWR-3/4"-20.5
BL-3000-SWR-3/4"-21.7		 19 18
20		 21.25 21.34 18.5
20.5
21.7		 31.5 13 13 80 22.3 47.6 52 65 M 10X40
BL-3000-SWR-1"-25.5
BL-3000-SWR-1"-27.3		 25 25 26.75 26.68 25.5
27.3		 38 19 14 90 26.2 52.4 59 70 M 10X45
BL-3000-SWR-1"1/4-30.5*
BL-3000-SWR-1"1/4-32.5*
BL-3000-SWR-1"1/4-34*
BL-3000-SWR-1"1/4-35.5*		 200 32 30
32
35		 33.50 33.50 30.5
32.5
34
35.5		 43 25 16 100 30.2 58.7 73 79.5 M 12X45*
BL-3000-SWR-1"1/2-38.5*
BL-3000-SWR-1"1/2-40.7*
BL-3000-SWR-1"1/2-43*		 38 38
40
42		 42.25 42.16 38.5
40.7
43		 50 32 18 110 35.7 69.8 83 94 M 14X50*
BL-3000-SWR-2"-49*
BL-3000-SWR-2"-50.7*		 51 50 48.25 48.26 49
50.7		 61.8 38 20 130 42.9 77.8 97 102 M 14X50*
BL-3000-SWR-2"1/2-61*
BL-3000-SWR-2"1/2-65.8*		 150 64 60
65		 60.30 60.30 61
65.8		 73.8 47 22 150 50.8 88.9 109 114.5 M 14X55*
BL-3000-SWR-3"-74
BL-3000-SWR-3"-77		 100 76   76.10 73.02 74
77		 90 58 24 170 61.9 106.4 131 135 M 16X65
BL-3000-SWR-3"-81   80     81                  

(1)Pressure max. recommended
Flanges with 0'Ring and metric bold.
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order.
BRIDES DE LIAISON SOCKET WELDING A PASSAGE REDUIT

UNION ASSEMBLY FLANGES REDUCING SOCKET WELDING
S.A.E. 6000 – ISO 6162-2
Part N° PN Bar1 DN Outer diameter tube ØL1 ØL2 ØA K L GG Q FF O Bolts
Metric
MM GAZ SCHD
BL-6000-SWR-1/2"-16.5
BL-6000-SWR-1/2"-17.6		 380 13 16 16,75 17.14 16.5
17.6		 24 11 13 70 18.2 40.5 48 56.5 M 8X45
BL-6000-SWR-3/4"-18.5
BL-6000-SWR-3/4"-20.5
BL-6000-SWR-3/4"-21.7		 19 18
20		 21.25 21.34 18.5
20.5
21.7		 31.8 13 13 80 23.8 50.8 60 71 M 10X50
BL-6000-SWR-1"-25.5
BL-6000-SWR-1"-27.3		 25 25 26.75 26.68 25.5
27.3		 38 17.5 13 90 27.8 57.2 70 81 M 12X65
BL-6000-SWR-1"1/4-30.5*
BL-6000-SWR-1"1/4-32.5*
BL-6000-SWR-1"1/4-34*		 300 32 30
32		 33.50 33.40 30.5
32.5
34		 44 22 16 100 31.8 66.6 78 95 M 14X70
BL-6000-SWR-1"1/4-35.5* 35     35.5
BL-6000-SWR-1"1/2-38.5   38     38.5                  
BL-6000-SWR-1"1/2-40.5
BL-6000-SWR-1"1/2-42.8		 38 40
42		 42.25 42.16 40.5
42.8		 51 29 18 110 36.5 79.3 95 113 M 16X80
BL-6000-SWR-2"-49
BL-6000-SWR-2"-50.8		 51 50 48.25 48.26 49
50.8		 67 35 20 130 44.5 96.8 114 133 M 20X100

(1)Pressure max. recommended
Flanges with 0'Ring and metric bold.
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order.
+ -

UNION ASSEMBLY FLANGES SOCKET WELD TUBE END
SAE 3000
Click to collapse
BRIDES DE LIAISON SOCKET WELDING INTEGRAL

UNION ASSEMBLY FLANGES SOCKET WELD TUBE END
SAE 3000 / ISO 6162-1
Part N° PN Bar1 DN Outer diameter tube Ø L1 Ø L2 Ø A K L Bolts
Metric
MM GAZ SCHD
BL-3000-SWI-1/2"-20.5
BL-3000-SWI-1/2"-21.7		 315 13 20 21.15 21.34 20.5
21.7		 30 13 13 80 M 8X25
BL-3000-SWI-3/4"-25.5 19 25     25.5 35 19 13 88 M 10X30
BL-3000-SWI-3/4"-27.3 26.75 26.68 27.3
BL-3000-SWI-1"-30.5
BL-3000-SWI-1"-32.5
BL-3000-SWI-1"-34
BL-3000-SWI-1"-35.5		 25 30
32
35		 33.50 33.40 30.5
32.5
34
35.5		 44 25 16 100 M 10X30 *
BL-3000-SWI-1"1/4-38.5 *
BL-3000-SWI-1"1/4-40.5 *		 200 32 38
40		     38.5
40.5		 55 32 18 120 M 12X30 *
BL-3000-SWI-1"1/4-43 *   42 42.25 42.16 43          
BL-3000-SWI-1"1/2-49 *
BL-3000-SWI-1"1/2-50.4 *		 38 50 48.25 48.26 49
50.4		 63 38 20 130 M 14X35 *
BL-3000-SWI-2"-61 * 51 60 60.30 60.32 61 79 47 22 147 M 14X35 *
BL-3000-SWI-2"-65.8 * 65   65.8 65.8
BL-3000-SWI-2"1/2-74 *
BL-3000-SWI-2"1/2-77 *
BL-3000-SWI-2"1/2-81 *		 150 64 80 76.10 73.02 74
77
81		 98 58 24 170 M 14X40 *
BL-3000-SWI-3"-90.5 100 76 90   88.90 90.5 116 70 28 190 M 16X50

(1)Pressure max. recommended
Flanges with 0'Ring and metric bolts

Port assembly shutter

+ -

PORT ASSEMBLY SHUTTER FLANGES WITH PLUGS
SAE 3000 / SAE 6000
Click to collapse
BRIDES D'OBTURATION EN DEUX PARTIES
PORT ASSEMBLY SHUTTER FLANGES WITH PLUGS
S.A.E. 3000 – ISO 6162-1
Part N° PN bar1 DN L GG Q FF O Bolts
Metric UNC
BFX-OB-3000-1/2"
BFX-OB-3000-3/4"		 350 13
19		 15
16		 17.5
22.3		 38.1
47.6		 46
52		 54
65		 M 8X25
M 10X30		 5/16-1"1/4
3/8-1"1/4
BFX-OB-3000-1" 315 25 18 26.2 52.4 59 70 M 10X35 3/8-1"1/4
BFX-OB-3000-1"1/4 * 250 32 18 30.2 58.7 73 79.5 M 12X35 * 7/16-1"1/4
BFX-OB-3000-1"1/2 *
BFX-OB-3000-2" *		 210 38
51		 18
21		 35.7
42.9		 69.8
77.8		 83
97		 94
102		 M 14X40*
M 14X40*		 1/2-1"1/2
1/2-1"1/2
BFX-OB-3000-2"1/2 * 160 64 21 50.8 88.9 109 114.5 M 14X45* 1/2-1"3/4
BFX-OB-3000-3" 138 76 24 61.9 106.4 131 135 M 16X50 5/8-2"
BFX-OB-3000-3"1/2 35 89 45 69.8 120.7 140 152 M 16X50 5/8-2"
BFX-OB-3000-4" 35 102 55 77.8 130.2 152 162 M 16X50 5/8-2"

(1)Pressure max. recommended
Flanges with 0'Ring and metric bolts.
For metric bolts, add "M" after the reference ; for UNC bolts, add "U". Standard delivered with undivided split flanges, specify for split flanges.
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order


PORT ASSEMBLY SHUTTER FLANGES WITH PLUGS
S.A.E. 6000 – ISO 6162-2
Part N° PN bar1 DN L GG Q FF O Bolts
Metric UNC
BFX-OB-6000-1/2" 400 13 18 18.2 40.5 48 56.5 M 8X30 5/16-1"1/4
BFX-OB-6000-3/4" 19 21 23.8 50.8 60 71 M 10X35 3/8-1"1/2
BFX-OB-6000-1" 25 26 27.8 57.2 70 81 M 12X45 7/16-1"3/4
BFX-OB-6000-1"1/4 * 32 31 31.8 66.6 78 95 M 14X50* 1/2-2"
BFX-OB-6000-1"1/2 38 34 36.5 79.3 95 113 M 16X55 5/8-2"1/4
BFX-OB-6000-2" 51 42 44.5 96.8 114 133 M 20X70 3/4-2"3/4

(1)Pressure max. recommended
Flanges with 0'Ring and metric bolts.
For metric bolts, add "M" after the reference ; for UNC bolts, add "U". Standard delivered with undivided split flanges, specify for split flanges.
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order
+ -

BLANKS SHUTTER FLANGES
SAE 3000 / SAE 6000
Click to collapse
BRIDES D'OBTURATION MONOBLOC
BLANKS SHUTTER FLANGES
S.A.E. 3000 – ISO 6162-1
Part N° PN bar1 DN GG Q FF O E F Ø H* Bolts
Metric UNC
BFX-OB-MONO-3000-1/2" 350 13 17.5 38.1 47 57 16 14 10 M 8 5/16"
BFX-OB-MONO-3000-3/4" 19 22.3 47.6 49 66 18 16 15 M 10 3/8"
BFX-OB-MONO-3000-1" 315 25 26.2 52.4 53 71 19 16 18 M 10 3/8"
BFX-OB-MONO-3000-1"1/4 * 250 32 30.2 58.7 69 80 21 18 23 M 10 ou
M 12		 7/16"
BFX-OB-MONO-3000-1"1/2 * 210 38 35.7 69.8 77 95 24 19 28 M 12 ou
M 14		 1/2"
BFX-OB-MONO-3000-2" * 51 42.9 77.8 89 103 24 19 45 M 12 ou
M 14		 1/2"
BFX-OB-MONO-3000-2"1/2 * 160 64 50.8 88.9 101 116 25 19 58 M 12 ou
M 14		 1/2"
BFX-OB-MONO-3000-3" 138 76 61.9 106.4 124 136 25 27 70 M 16 5/8"
BFX-OB-MONO-3000-3"1/2 35 89 69.8 120.7 136 152 25 27 85 M 16 5/8"
BFX-OB-MONO-3000-4" 35 102 77.8 130.2 146 162 25 27 95 M 16 5/8"
BFX-OB-MONO-3000-5" 35 127 92 152.4 180 184 25 27 110 M 16 5/8"

(1)Pressure max. recommended
Flanges with 0'Ring and metric bolts.
For metric bolts, add "M" after the reference ; for UNC bolts, add "U". Standard delivered with undivided split flanges, specify for split flanges.
*On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order


BLANKS  SHUTTER FLANGES
S.A.E. 6000 – ISO 6162-2
Part N° PN bar1 DN GG Q FF O E F Ø H* Bolts
Metric UNC
BFX-OB-MONO-6000-1/2" 400 13 18.2 40.5 47 57 16 14 10 M 8 5/16"
BFX-OB-MONO-6000-3/4" 19 23.8 50.8 53 71 19 16 15 M 10 3/8"
BFX-OB-MONO-6000-1" 25 27.8 57.2 66 80 24 18 22 M 12 7/16"
BFX-OB-MONO-6000-1"1/4 * 32 31.8 66.6 77 94 27 24 30 M 14 ou M12 1/2"
BFX-OB-MONO-6000-1"1/2 38 36.5 79.3 89 103 30 24 35 M 16 5/8"
BFX-OB-MONO-6000-2" 51 44.5 96.8 123 135 35 31 48 M 20 3/4"

(1)Pressure max. recommended
Flanges with 0'Ring and metric bolts.
For metric bolts, add "M" after the reference ; for UNC bolts, add "U". Standard delivered with undivided split flanges, specify for split flanges.
*On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

Counter flanges

+ -

COUNTER FLANGES FEMALE BSPP THREAD OR NPT
SAE 3000 / SAE 6000
Click to collapse
BRIDES SANS GORGE TARAUDEES BSPP OU NPT
COUNTER FLANGES FEMALE BSPP THREADOR NPT
S.A.E. 3000 –ISO 6162-1
Part N° PN
bar1		 DN Ø F BSP ØA L GG Q FF O U K Bolts
Metric UNC
BAS-3000-T-BSP-1/2" 345 13 1/2" 13 36 17.5 38.1 47 57 16 19 M 8 5/16"
BAS-3000-T-BSP-3/4" 19 3/4" 19 36 22.3 47.6 49 66 18 19 M 10 3/8"
BAS-3000-T-BSP-1" 25 1" 25 38 26.2 52.4 53 71 18 19 M 10 3/8"
BAS-3000-T-BSP-1"1/4 * 278 32 1"1/4 31 41 30.2 58.7 69 80 21 22 M 10 ou
M 12*		 7/16"
BAS-3000-T-BSP-1"1/2 * 210 38 1"1/2 38 44 35.7 69.8 77 94 25 24 M 12 ou
M 14*		 1/2"
BAS-3000-T-BSP-2" * 51 2" 50 45 42.9 77.8 89 103 25 26 M 12 ou
M 14*		 1/2"
BAS-3000-T-BSP-2"1/2 * 175 64 2"1/2 63 50 50.8 88.9 101 115 25 30 M 12 ou
M 14*		 1/2"
BAS-3000-T-BSP-3" 138 76 3" 73 50 61.9 106.4 124 135 27 34 M 16 5/8"
BAS-3000-T-BSP-3"1/2 35 89 3"1/2 89 50 69.8 120.7 136 152 27 30 M 16 5/8"
BAS-3000-T-BSP-4" 102 4" 99 50 77.8 130.2 146 162 27 30 M 16 5/8"

(1)Pressure max. recommended
For metric bolts, add "M" after the reference ; for UNC bolts, add "U".
For tapped NPT, replace BSP by NPT into the reference.
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order


COUNTER FLANGES FEMALE BSPP THREADOR NPT
S.A.E. 6000 – ISO 6162-2
Part N° PN
bar1		 DN Ø F BSP ØA L GG Q FF O U K Bolts
Metric UNC
BAS-6000-T-BSP-1/2" 400 13 1/2" 13 36 18.2 40.5 47 57 16 19 M 8 5/16"
BAS-6000-T-BSP-3/4" 19 3/4" 19 36 23.8 50.8 53 71 19 22 M 10 3/8"
BAS-6000-T-BSP-1" 25 1" 25 44 27.8 57.2 69 80 24 24 M 12 7/16"
BAS-6000-T-BSP-1"1/4 * 32 1"1/4 31 44 31.8 66.6 77 94 27 25 M 14 ou
M 12*		 1/2"
BAS-6000-T-BSP-1"1/2 38 1"1/2 38 51 36.5 79.3 89 106 30 28 M 16 5/8"
BAS-6000-T-BSP-2" 51 2" 50 70 44.5 96.8 116 135 37 33 M 20 3/4"

(1)Pressure max. recommended
For metric bolts, add "M" after the reference ; for UNC bolts, add "U".
For tapped NPT, replace BSP by NPT into the reference.
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order
+ -

COUNTER FLANGES BUTT WELDING TUBE END (MONOBLOC) BWI
SAE 3000 / SAE 6000
Click to collapse
BRIDES SANS GORGE TARAUDEES BSPP OU NPT
COUNTER FLANGES BUTT WELDING TUBE END (MONOBLOC) BWI
S.A.E. 3000 –ISO 6162-1
Part N° PN
bar1		 DN ØA ØB L GG Q FF U O Bolts
Metric UNC
BAS-MATRI-3000- BWI-1/2"-21.5 345 13 21.6 13 36 17.5 38 47 16 57 M 8 5/16"
BAS-MATRI-3000-BWI-3/4"-27 19 27.2 19 36 22.3 47.6 49 18 66 M 10 3/8"
BAS-MATRI-3000-BWI-1"-34 315 25 34.5 25 38 26.2 52.4 53 18 71 M 10 3/8"
BAS-MATRI-3000-BWI-1"1/4-42* 250 32 42.8 31 41 30.2 58.7 69 21 80 M 10 ou
M 12*		 7/16"
BAS-MATRI-3000-BWI-1"1/2-48.6* 210 38 48.6 38 44 35.7 69.8 77 25 94 M 12 ou
M 14*		 1/2"
BAS-MATRI-3000-BWI-2"-61* 51 61 50 45 42.9 77.8 89 25 103 M 12 ou
M 14*		 1/2"
BAS-MATRI-3000-BWI-2"1/2-77* 160 64 76.6 63 50 50.8 88.9 101 25 115 M 12 ou
M 14*		 1/2"
BAS-MATRI-3000-BWI-3"-90.5 138 76 89 73 50 61.9 106.4 124 27 135 M 16 5/8"
BAS-MATRI-3000-BWI-3"1/2-103 35 89 103 89 50 70 120.7 137 27 153 M 16 5/8"
BAS-MATRI-3000-BWI-4"-115 102 115 99 50 77.8 130 147 27 163 M 16 5/8"

(1)Pressure max. recommended
For metric bolts, add "M" after the reference ; for UNC bolts, add "U".
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order


COUNTER FLANGES BUTT WELDING TUBE END (MONOBLOC) BWI
S.A.E. 6000 – ISO 6162-2
Part N° PN
bar1		 DN ØA ØB L GG Q FF U O Bolts
Metric UNC
BAS-MATRI-6000-BWR-1/2"-17.5 400 13 17.5 10 36 18.2 40.5 47 16 57 M 8 5.16"
BAS-MATRI-6000-BWI-1/2"-21.6 13 21.6 13 36 18.2 40.5 47 16 57 M 8 5/16"
BAS-MATRI-6000-BWI-3/4"-27.2 19 27.2 18 36 23.8 50.8 53 19 71 M 10 3/8"
BAS-MATRI-6000-BWI-1"-34.5 25 34.5 22 44 27.8 57.2 66 24 80 M 12 7/16"
BAS-MATRI-6000-BWI-1"1/4-42.8* 32 42.8 28 44 31.6 66.7 77 27 94 M 14* 1/2"
BAS-MATRI-6000-BWI-1"1/2-48.6 38 48.6 32 51 36.7 79.4 89 30 106 M 16 5/8"
BAS-MATRI-6000-BWI-2"-61 51 61 41 58 44.4 96.8 116 37 135 M 20 3/4"

(1)Pressure max. recommended
For metric bolts, add "M" after the reference ; for UNC bolts, add "U".
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order
+ -

COUNTER FLANGES SWI (MONOBLOC)
SAE 3000 / SAE 6000
Click to collapse
BRIDES A SOUDER MATRICEES SANS GORGE SWI
COUNTER FLANGES SWI (MONOBLOC)
S.A.E. 3000 –ISO 6162-1
Part N° PN
bar1		 DN ØA ØB L GG Q FF U K O Bolts
Metric UNC
BAS-MATRI-3000-SWI-1/2"-21.6 345 13 21.6 13 36 17.5 38.1 47 16 18 57 M 8 5/16"
BAS-MATRI-3000-SWI-3/4"-27.2 19 27.2 19 36 22.3 47.6 49 18 18 66 M 10 3/8"
BAS-MATRI-3000-SWI-1"-34 25 34.1 25 38 26.2 52.4 53 18 18 71 M 10 3/8"
BAS-MATRI-3000-SWI-1"1/4-43* 278 32 42.8 31 41 30.2 58.7 69 21 20 80 M 10 ou
M 12*		 7/16"
BAS-MATRI-3000-SWI-1"1/2-49* 210 38 48.6 38 44 35.7 69.8 77 25 22 94 M 12 ou
M 14*		 1/2"
BAS-MATRI-3000-SWI-2"-61* 51 61 50 45 42.9 77.8 89 25 24 103 M 12 ou
M 14 *		 1/2"
BAS-MATRI-3000-SWI-2"1/2-77* 175 64 76.6 63 50 50.8 88.9 101 25 28 115 M 12 ou
M 14*		 1/2"
BAS-MATRI-3000-SWI-3"-90.5 138 76 90.5 73 50 61.9 106.4 124 27 28 135 M 16 5/8"

(1)Pressure max. recommended
- DN 3"1/2 and 4" on request
For metric bolts, add "M" after the reference ; for UNC bolts, add "U".
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order


COUNTER FLANGES SWI (MONOBLOC)
S.A.E. 6000 – ISO 6162-2
Part N° PN
bar1		 DN ØA ØB L GG Q FF U K O Bolts
Metric UNC
BAS-MATRI-6000-SWI-1/2"-21.6 400 13 21.6 13 36 18.2 40.5 47 16 18 57 M 8 5/16"
BAS-MATRI-6000-SWI-3/4"-27.2 19 27.2 19 36 23.8 50.8 53 19 20 71 M 10 3/8"
BAS-MATRI-6000-SWI-1"-34 25 34.1 25 44 27.8 57.2 66 24 22 80 M 12 7/16"

(1)Pressure max. recommended
- Until 2" on request
For metric bolts, add "M" after the reference ; for UNC bolts, add "U".
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order
+ -

CONTER FLANGES SOCKET WELD TUBE END
SAE 3000
Click to collapse
BRIDES A SOUDER SOCKET WELDING INTEGRAL

CONTER FLANGES SOCKET WELD TUBE END
SAE 3000 – ISO 6162-1
Part N° GG O Q FF Ø L1 Ø A K U Bolts
BAS-3000-SWI-1/2"-20.5
BAS-3000-SWI-1/2"-21.7		 17.5 54 38.1 45 20.5
21.7		 13 13 20 M 8
BAS-3000-SWI-3/4"-25.5
BAS-3000-SWI-3/4"-27.3		 22.3 65 47.6 55 25.5
27.3		 19 13 20 M 10
BAS-3000-SWI-1"-30.5
BAS-3000-SWI-1"-32.5
BAS-3000-SWI-1"-34
BAS-3000-SWI-1"-35.5		 26.2 70 52.4 60 30.5
32.5
34
35.5		 25 16 25 M 10
BAS-3000-SWI-1"1/4-38.5 *
BAS-3000-SWI-1"1/4-40.5 *
BAS-3000-SWI-1"1/4-43 *		 30.2 80 58.7 73 38.5
40.5
43		 32 18 25 M 12
ou
M 10 (ISO)
BAS-3000-SWI-1"1/2-49 *
BAS-3000-SWI-1"1/2-50.4 *		 35.7 94 69.8 80 49
50.4		 38 20 30 M 14
ou M 12 (ISO)
BAS-3000-SWI-2"-61 *
BAS-3000-SWI-2"-65.8 *		 42.9 100 77.8 97 61
65.8		 47 24 40 M 14
ou M 12 (ISO)
BAS-3000-SWI-2"1/2-74 *
BAS-3000-SWI-2"1/2-77 *
BAS-3000-SWI-2"1/2-81 *		 50.8 114 88.9 110 74
77
81		 58 24 40 M 14
ou
M 12 (ISO)
BAS-3000-SWI-3"-90.5 61.9 135 106.4 131 90.5 70 28 40 M 16

(1)Pressure max. recommended
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

Blocks

+ -

PORT ELBOW
SAE 3000 / SAE 6000
Click to collapse
BLOCS EQUERRES DE FIXATION

SAE 3000

PORT ELBOW
S.A.E. 3000 – ISO 6162-1
Part N° PN Bar1 DN Ø A FF O D Q GG Screw Bolts
Metric UNC Metric UNC
BLC-EQ-FIX-3000-3/8"
BLC-EQ-FIX-3000-1/2"		 350 10
13		 12
13		 41
46		 52
58		 50
56		 35
38.1		 16.5
17.5		 M 8X55
M 8X60		 -
5/16"-2"1/4		 M 8
M 8		 -
5/16"
BLC-EQ-FIX-3000-3/4 19 19 53 66 66 47.6 22.3 M 10X70 3/8"-2"3/4 M 10 3/8"
BLC-EQ-FIX-3000-1"
BLC-EQ-FIX-3000-1"1/4 *		 315 25
32		 25
32		 60
75		 72
80		 80
95		 52.4
58.7		 26.2
30.2		 M 10X75
M 12X90		 3/8"-3"
7/16"-3"1/2		 M 10
M 12 *		 3/8"
7/16"
250
BLC-EQ-FIX-3000-1"1/2 * 210 38 38 85 95 110 69.8 35.7 M 14X110 1/2"-4"1/2 M 14 * 1/2"
BLC-EQ-FIX-3000-2" *
BLC-EQ-FIX-3000-2"1/2 *		 51
64		 47
58		 100
110		 108
118		 110
125		 77.7
88.9		 42.9
50.8		 M 14X120
M 14X130		 1/2"-5"
1/2"-5"		 M 14 *
M 14 *		 1/2"
1/2"
160
BLC-EQ-FIX-3000-3" 138 76 70 132 138 150 106.4 61.9 M 16X160 5/8"-6"1/2 M 16 5/8"

(1)Pressure max. recommended
blocks with 0'Ring and bolts
For metric bolts, add "M" after the reference ; for UNC bolts, add "U".
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

SAE 6000

PORT ELBOW
S.A.E. 6000 – ISO 6162-2
Part N° PN Bar1 DN Ø A FF O D Q GG Screw Bolts
Metric UNC Metric UNC
BLC-EQ-FIX-6000-1/2"
BLC-EQ-FIX-6000-3/4"		 400 13
19		 13
17.5		 50
62		 58
73		 56
66		 40.5
50.8		 18.2
23.8		 M 8X65
M 10X80		 5/16"-2"1/2
3/8"-3"1/4		 M 8
M 10		 5/16"
3/8"
BLC-EQ-FIX-6000-1" 25 22 72 83 80 57.2 27.8 M 12X90 7/16"-3"1/2 M 12 7/16"
BLC-EQ-FIX-6000-1"1/4 *
BLC-EQ-FIX-6000-1"1/2		 32
38		 29
35		 80
98		 98
115		 95
110		 66.6
79.3		 31.8
36.5		 M 14X100*
M 16X120		 1/2"-4"
5/8"-5"		 M 14 *
M 16		 1/2"
5/8"
BLC-EQ-FIX-6000-2" 51 43 116 135 135 96.8 44.5 M 20X150 3/4"-6" M 20 3/4"

(1)Pressure max. recommended
Blocks with 0'Ring and bolts
For metric bolts, add "M" after the reference ; for UNC bolts, add "U".
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order
+ -

"L" BLOCKS
SAE 3000 / SAE 6000
Click to collapse
BLOCS DE DISTRIBUTION EN L

SAE 3000

"L" BLOCKS
S.A.E. 3000 – ISO 6162-1
Part N° PN Bar1 DN Ø A O FF C GG Q Bolts
Metric UNC
BLC-DIST-L-3000-3/8"
BLC-DIST-L-3000-1/2"		 350 10
13		 12
13		 52
58		 41
46		 50
56		 16.5
17.5		 35
38.1		 M 8
M 8		 -
5/16"
BLC-DIST-L-3000-3/4" 19 19 66 53 66 22.3 47.6 M 10 3/8"
BLC-DIST-L-3000-1"
BLC-DIST-L-3000-1"1/4*		 315 25
32		 25
32		 72
80		 60
75		 80
95		 26.2
30.2		 52.4
58.7		 M 10
M 12 *		 3/8"
7/16"
250
BLC-DIST-L-3000-1"1/2* 210 38 38 95 85 110 35.7 69.8 M 14 * 1/2"
BLC-DIST-L-3000-2"*
BLC-DIST-L-3000-2"1/2*		 51
64		 47
58		 108
118		 100
110		 110
125		 42.9
50.8		 77.8
88.9		 M 14 *
M 14 *		 1/2"
1/2"
160
BLC-DIST-L-3000-3" 138 76 70 138 132 150 61.9 106.4 M 16 5/8"

(1)Pressure max. recommended
For metric bolts, add "M" after the reference ; for UNC bolts, add "U".
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

SAE 6000

"L" BLOCKS
S.A.E. 6000 – ISO 6162-2
Part N° PN Bar1 DN Ø A O FF C GG Q Bolts
Metric UNC
BLC-DIST-L-6000-1/2"
BLC-DIST-L-6000-3/4"		 400 13
19		 13
17.5		 58
73		 50
62		 56
66		 18.2
23.8		 40.5
50.8		 M 8
M 10		 5/16"
3/8"
BLC-DIST-L-6000-1" 25 22 83 72 80 27.8 57.2 M 12 7/16"
BLC-DIST-L-6000-1"1/4*
BLC-DIST-L-6000-1"1/2		 32
38		 29
35		 98
115		 80
98		 95
110		 31.8
36.5		 66.6
79.3		 M 14 *
M 16		 1/2"
5/8"
BLC-DIST-L-6000-2" 51 43 135 116 135 44.5 96.8 M 20 3/4"

(1)Pressure max. recommended
For metric bolts, add "M" after the reference ; for UNC bolts, add "U".
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order
[/tabs]
+ -

"T" BLOCKS
SAE 3000 / SAE 6000
Click to collapse
BLOCS DE DISTRIBUTION EN T

SAE 3000

"T" BLOCKS
S.A.E. 3000 – ISO 6162-1
Part N° PN
bar1		 DN Ø A O FF C GG Q Bolts
Metric UNC
BLC-DIST-T-3000-3/8"
BLC-DIST-T-3000-1/2"		 350 10
13		 12
13		 52
58		 41
46		 50
56		 16.5
17.5		 35
38.1		 M 8
M 8		 -
5/16"
BLC-DIST-T-3000-3/4" 19 19 66 53 66 22.3 47.6 M 10 3/8"
BLC-DIST-T-3000-1"
BLC-DIST-T-3000-1"1/4*		 315 25
32		 25
32		 72
80		 60
75		 80
95		 26.2
30.2		 52.4
58.7		 M 10
M 12 *		 3/8"
7/16"
250
BLC-DIST-T-3000-1"1/2* 210 38 38 95 85 110 35.7 69.8 M 14 * 1/2"
BLC-DIST-T-3000-2"*
BLC-DIST-T-3000-2"1/2*		 51
64		 47
58		 108
118		 100
110		 110
125		 42.9
50.8		 77.7
88.9		 M 14 *
M 14 *		 1/2"
1/2"
160
BLC-DIST-T-3000-3" 138 76 70 138 132 150 61.9 106.4 M 16 5/8"

(1)Pressure max. recommended
For metric bolts, add "M" after the reference ; for UNC bolts, add "U".
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

SAE 6000

"T" BLOCKS
S.A.E. 6000 – ISO 6162-2
Part N° PN
bar1		 DN Ø A O FF C GG Q Bolts
Metric UNC
BLC-DIST-T-6000-1/2"
BLC-DIST-T-6000-3/4"		 400 13
19		 13
17.5		 58
73		 50
62		 56
66		 18.2
23.8		 40.5
50.8		 M 8
M 10		 5/16"
3/8"
BLC-DIST-T-6000-1" 25 22 83 72 80 27.8 57.2 M 12 7/16"
BLC-DIST-T-6000-1"1/4*
BLC-DIST-T-6000-1"1/2		 32
38		 29
35		 98
115		 80
98		 95
110		 31.8
36.5		 66.6
79.3		 M 14 *
M 16		 1/2"
5/8"
BLC-DIST-T-6000-2" 51 43 135 116 135 44.5 96.8 M 20 3/4"

(1)Pressure max. recommended
For metric bolts, add "M" after the reference ; for UNC bolts, add "U".
* On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order
+ -

"X" BLOCKS
SAE 3000 / SAE 6000
Click to collapse
BLOCS DE DISTRIBUTION EN X
"X" BLOCKS
S.A.E. 3000 – ISO 6162-1
Part N° PN
bar1		 DN Ø A O FF C GG Q Bolts
Metric UNC
BLC-DIST-X-3000-3/8"
BLC-DIST-X-3000-1/2"		 350 10
13		 12
13		 52
58		 41
46		 60
68		 16.5
17.5		 35
38.1		 M 8
M 8		 -
5/16"
BLC-DIST-X-3000-3/4" 19 19 66 53 82 22.3 47.6 M 10 3/8"
BLC-DIST-X-3000-1"
BLC-DIST-X-3000-1"1/4*		 315 25
32		 25
32		 72
80		 60
75		 95
110		 26.2
30.2		 52.4
58.7		 M 10
M 12 *		 3/8"
7/16"
250
BLC-DIST-X-3000-1"1/2* 210 38 38 95 85 120 35.7 69.8 M 14 * 1/2"
BLC-DIST-X-3000-2"*
BLC-DIST-X-3000-2"1/2*		 51
64		 47
58		 108
118		 100
110		 120
130		 42.9
50.8		 77.7
88.9		 M 14 *
M 14 *		 1/2"
1/2"
160
BLC-DIST-X-3000-3" 138 76 70 138 132 160 61.9 106.4 M 16 5/8"

(1)Pressure max. recommended
For metric bolts, add "M" after the reference ; for UNC bolts, add "U".
On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order


"X" BLOCKS
S.A.E. 6000 – ISO 6162-2
Part N° PN
bar1		 DN Ø A O FF C GG Q Bolts
Metric UNC
BLC-DIST-X-6000-1/2"
BLC-DIST-X-6000-3/4"		 400 13
19		 13
17.5		 58
73		 50
62		 68
82		 18.2
23.8		 40.5
50.8		 M 8
M 10		 5/16"
3/8"
BLC-DIST-X-6000-1" 25 22 83 72 94 27.8 57.2 M 12 7/16"
BLC-DIST-X-6000-1"1/4*
BLC-DIST-X-6000-1"1/2		 32
38		 29
35		 98
115		 80
98		 110
130		 31.8
36.5		 66.6
79.3		 M 14 *
M 16		 1/2"
5/8"
BLC-DIST-X-6000-2" 51 43 135 116 140 44.5 96.8 M 20 3/4"

(1)Pressure max. recommended
For metric bolts, add "M" after the reference ; for UNC bolts, add "U".
On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

Square flanges - PN 250/ PN 400

Square flanges

BRIDES CARREES CETOP SIDERURGIE MONOBLOC
SQUARE FLANGES CETOP-SIDERURGIE
PN 250 / CETOP
Part N° PN bar1 DN O GG Ø J Ø D U F T
BM-250-CET-3/8"
BM-250-CET-1/2"		 250 10
13		 40
45		 24.7
29.7		 18.5
24.3		 25.1
31		 14 *
15 *		 6.2
6.2		 6.5
8.5
BM-250-SID-1/2" 13 45 30 24.3 31 15 6.2 6.5
BM-250-CET-SID-3/4"
BM-250-CET-SID-1"		 19
25		 50
65		 35.3
43.8		 32.1
38.5		 38.9
45.3		 16 *
18 *		 6.2
7.6		 8.5
11
BM-250-CET-SID-1"1/4 32 75 51.6 43.7 51.6 22 * 7.6 13
BM-250-CET-1"1/2
BM-250-SID-1"1/2		 38
38		 85*
85		 60,1
60		 50.8
50.8		 61.1
61.1		 25 *
25		 7.6
7.6		 15 *
13
BM-250-CET-2" 51 100 69.3 62.7 72.2 30 * 9 17
BM-250-SID-2"
BM-250-CET-2"1/2		 51
56		 100
120		 68
83.4		 62.7
76.6		 72.2
88		 30
35 *		 9
9		 15
21
BM-250-SID-2"1/2 56 120 85 76.6 88 35 9 19
BM-250-CET-3"
BM-250-SID-3"		 63
63		 140
140		 102.5
95		 90.8
90.8		 102.3
102.3		 40 *
40		 9
9		 21
23
BM-250-CET-3"1/2 70 140 * 102.5 * 102.5 120 52 * 17.5 21 *
BM-250-CET-4"
BM-250-SID-4"		 80
80		 160 *
180		 113.2 *
130		 114.5
114.5		 132
132		 60 *
60		 21
21		 21 *
25

(1)Pressure max. recommended
On request can be delivered with ISO 6164


SQUARE FLANGES CETOP-SIDERURGIE
PN 400 / CETOP
Part N° PN bar1 DN O GG Ø J Ø D U F T
BM-400-CET-3/8"
BM-400-CET-1/2"		 400 10
13		 40
45		 24.7
29.7		 18.5
24.6		 26.5
32.5		 16 *
17 *		 7.4
7.4		 6.5
8.5
BM-400-CET-3/4" 19 50 35.4 32.5 40 20 * 8.4 8.5
BM-400-CET-1"
BM-400-CET-1"1/4		 25
32		 65
75		 43.8
51.6		 38.5
44.5		 48.4
54.8		 24 *
28 *		 9.1
9.9		 11
13
BM-400-CET-1"1/2 * 38 85 * 60,1 51.6 64.3 32 * 12.2 15 *
BM-400-CET-2"
BM-400-CET-2"1/2		 51
56		 100
120		 69.3
83.4		 67.6
80.5		 80.2
95		 40 *
45 *		 12.2
16.1		 17
21
BM-400-CET-3" * 63 140 * 102.5 90.5 105 52 * 16.1 21 *
BM-400-CET-3"1/2 *
BM-400-CET-4 *		 70
80		 140 *
160 *		 102.5 *
113.2 *		 102.5
114.5		 120
132		 52 *
60 *		 17.5
21		 21 *
25 *

(1)Pressure max. recommended
On request can be delivered with ISO 6164

Port assembly

+ -

PORT ASSEMBLY FLANGES BUTT WELDING CETOP-SIDERURGIE
PN250 / PN400
Click to collapse
BRIDES DE FIXATION BUTT WELDING INTEGRAL CETOP SIDERURGIE
PORT ASSEMBLY FLANGES BUTT WELDING CETOP-SIDERURGIE
PN 250* / CETOP
Part N° PN
bar1		 DN For tube
diameter to... at ...		 Ø A Ø H1 L 0 GG Bolts
Metric
BFX-250-BWI-CET-3/8"
BFX-250-BWI-CET-1/2"		 250 10
13		 14 - 18
18 - 22		 12
13		 18
22		 40
45		 40
45		 24.7
29.7		 6 X 25
8 X 30
BFX-250-BWI-SID-1/2" 13 18 - 22 13 22 45 45 30 6 X 25
BFX-250-BWI-CET-SID-3/4
BFX-250-BWI-CET-SID-1"		 19
25		 25 - 28
30 - 35		 19
25		 28
35		 50
55		 50
65		 35.3
43.8		 8 X 30
10 X 35
BFX-250-BWI-CET-SID-1"1/4 32 38 - 42.3 32 43 60 75 51.6 12 X 45
BFX-250-BWI-CET-1"1/2
BFX-250-BWI-SID-1"1/2		 38
38		 48 - 50
48 - 50		 38
38		 50
50		 65
65		 85
85		 60
60		 14 X 50
12 X 50
BFX-250-BWI-CET-2" 51 60 - 63.3 47 62 70 100 69.4 16 X 55
BFX-250-BWI-SID-2"
BFX-250-BWI-CET-2"1/2		 51
56		 60 - 63.3
73 - 80		 47
58		 62
76		 70
75		 100
120		 68
83.4		 14 X 55
20 X 70
BFX-250-BWI-SID-2"1/2 56 73 - 80 58 76 75 120 85 18 X 70
BFX-250-BWI-CET-3"
BFX-250-BWI-SID-3"		 63
63		 88 - 90
88 - 90		 70
70		 90
90		 85
85		 140
140		 102.5
95		 20 X 75
22 X 80
BFX-250-BWI-CET-3"1/2 70 95 - 102 77 102 90 140 102.5 20 X 90
BFX-250-BWI-CET-4"
BFX-250-BWI-SID-4"		 80
80		 113 - 120
113 - 120		 90
90		 118
118		 100
100		 160
180		 113.2
130		 24 X 100
27 X 100

(1)Pressure max. recommended
Flanges with 0'Ring and metric bolts.
On request can be delivered with ISO 6164


PORT ASSEMBLY FLANGES BUTT WELDING CETOP-SIDERURGIE
PN 400* / CETOP
Part N° PN bar1 DN For tube
diameter to... at ...		 Ø A Ø H1 L 0 GG Bolts
Metric
BFX-400-BWI-CET-3/8"
BFX-400-BWI-CET-1/2"		 400 10
13		 16 - 18
20 - 22		 11
13		 17.5
22		 40
45		 40
45		 24.7
29.7		 6 X 25
8 X 30
BFX-400-BWI-CET-3/4" 19 25 - 28 17.5 28 50 50 35.3 8 X 35
BFX-400-BWI-CET-1"
BFX-400-BWI-CET-1"1/4		 25
32		 33 - 35
42 - 45		 22
29		 35
43.8		 55
60		 65
75		 43.8
51.6		 10 X 40
12 X 45
BFX-400-BWI-CET-1"1/2 38 48 - 51 35 50.6 65 85 60 14 X 55
BFX-400-BWI-CET-2"
BFX-400-BWI-CET-2"1/2		 51
56		 60 - 65
75 - 80		 43
53		 65
76		 70
80		 100
120		 69.4
83.4		 16 X 65
20 X 80
BFX-400-BWI-CET-3" 63 80 - 90 58 90 90 140 102.5 20 X 90
BFX-400-BWI-CET-3"1/2
BFX-400-BWI-CET-4"		 70
80		 90 - 102
110 - 120		 63
74		 102
118		 90
110		 140
160		 102.5
113.2		 20 X 90
24 X 100

(1)Pressure max. recommended
Flanges with 0'Ring and metric bolts.
On request can be delivered with ISO 6164
+ -

PORT ASSEMBLY FLANGES REDUCING BUTT WELDING CETOP-SIDERURGIE
PN250 / PN400
Click to collapse
BRIDES DE LIAISON BUTT WELDING PASSAGE REDUIT CETOP SIDERURGIE
PORT ASSEMBLY FLANGES REDUCING BUTT WELDING CETOP-SIDERURGIE
PN 250* / CETOP
Part N° PN bar1 DN For tube
diameter to... at ...		 Ø A Ø H1 L 0 GG Bolts
Metric
BFX-250-BWR-CET-1/2"
BFX-250-BWR-SID-1/2"		 250 13
13		 14 - 18
14 - 18		 12
12		 18
18		 45
45		 45
45		 29.7
30		 8 X 30
6 X 25
BFX-250-BWR-CET-SID-3/4" 19 16 - 22 13 22 50 50 35.3 8 X 30
BFX-250-BWR-CET-SID-1"
BFX-250-BWR-CET-SID-1"1/4		 25
32		 25 - 28
30 - 35		 19
25		 28
35		 55
60		 65
75		 43.8
51.6		 10 X 35
12 X 45
BFX-250-BWR-CET-1"1/2 38 38 - 43 32 43 65 85 60 14 X 50
BFX-250-BWR-SID-1"1/2
BFX-250-BWR-CET-2"		 38
51		 38 - 43
48 - 50		 32
38		 43
50		 65
70		 85
100		 60
69.4		 12 X 50
16 X 55
BFX-250-BWR-SID-2" 51 48 - 50 38 50 70 100 68 14 X 55
BFX-250-BWR-CET-2"1/2
BFX-250-BWR-SID-2"1/2		 56
56		 60 - 63
60 - 63		 47
47		 62
62		 75
75		 120
120		 83.4
85		 20 X 70
18 X 70
BFX-250-BWR-CET-3" 63 73 -80 58 76 85 140 102.5 20 X 75
BFX-250-BWR-SID-3"
BFX-250-BWR-CET-3"1/2		 63
70		 73 - 80
88 - 90		 58
70		 76
90		 85
90		 140
140		 95
102.5		 22 X 75
20 X 90
BFX-250-BWR-CET-4" 80 95 - 102 80 102 100 160 113.2 24 X 100
BFX-250-BWR-SID-4" 80 95 - 102 80 102 100 180 130 27 X 100

(1)Pressure max. recommended
Flanges with 0'Ring and metric bolts.
On request can be delivered with ISO 6164


PORT ASSEMBLY FLANGES REDUCING BUTT WELDING CETOP-SIDERURGIE
PN 400* / CETOP
Part N° PN bar1 DN For tube
diameter to... at ...		 Ø A Ø H1 L 0 GG Bolts
Metric
BFX-400-BWR-CET-1/2"
BFX-400-BWR-CET-3/4"		 400 13
19		 16 - 18
20 - 22		 11
13		 17.5
22		 45
50		 45
50		 29.7
35.3		 8 X 30
8 X 35
BFX-400-BWR-CET-1" 25 25 - 28 17.5 28 55 65 43.8 10 X 40
BFX-400-BWR-CET-1"1/4
BFX-400-BWR-CET-1"1/2		 32
38		 30 - 35
38 - 43		 22
29		 35
43.8		 60
65		 75
85		 51.6
60		 12 X 45
14 X 55
BFX-400-BWR-CET-2" 51 48 - 51 35 50.6 65 100 69.4 16 X 65
BFX-400-BWR-CET-2"1/2
BFX-400-BWR-CET-3"		 56
63		 60 - 65
75 - 80		 43
53		 65
80		 70
90		 120
140		 83.4
102.5		 20 X 80
20 X 90
BFX-400-BWR-CET-3"1/2 70 88 - 90 58 90 90 140 102.5 20 X 90
BFX-400-BWR-CET-4" 80 100 - 102 63 102 110 160 113.2 24 X 100

(1)Pressure max. recommended
Flanges with 0'Ring and metric bolts.
On request can be delivered with ISO 6164
+ -

PORT ASSEMBLY FLANGES FEMALE BSP/NPT THREAD CETOP-SIDERURGIE
PN250 / PN400
Click to collapse
BRIDES DE FIXATION TARAUDEES BSP NPT
PORT ASSEMBLY FLANGES FEMALE BSP/NPT THREAD CETOP-SIDERURGIE
PN 250* / CETOP
Part N° PN bar1 DN Ø F Ø A K L O GG Bolts
Metric
BFX-250-T-BSP-CET-3/8"-A
BFX-250-T-BSP-CET-3/8"-B		 250 10 3/8"
1/4"		 12
10		 13
12		 23 40 24.7 M 6X25
BFX-250-T-BSP-CET-1/2"-A 13 1/2" 14 15 32 45 29.7 M 8X35
BFX-250-T-BSP-CET-1/2"-B 3/8" 13 13
BFX-250-T-BSP-SID-1/2"-A
BFX-250-T-BSP-SID-1/2"-B		 13 1/2"
3/8"		 14
13		 15
13		 32 45 30 M 6X35
BFX-250-T-BSP-CET-SID-3/4"-A 19 3/4" 20 18 32 50 35.3 M 8X35
BFX-250-T-BSP-CET-SID-3/4"-B 1/2" 18 15
BFX-250-T-BSP-CET-SID-1"-A
BFX-250-T-BSP-CET-SID-1"-B		 25 1"
3/4"		 25
22		 20
18		 36 65 43.8 M 10X40
BFX-250-T-BSP-CET-SID-1"1/4-A 32 1"1/4 32 22 38 75 51.6 M 12X45
BFX-250-T-BSP-CET-SID-1"1/4-B 1" 28 20
BFX-250-T-BSP-CET-1"1/2-A
BFX-250-T-BSP-CET-1"1/2 B		 38 1"1/2
1"1/4		 38
36		 24
22		 42 85 60 M 14X50
BFX-250-T-BSP-SID-1"1/2-A 38 1"1/2 38 24 42 85 60 M 12X50
BFX-250-T-BSP-SID-1"1/2-B 1"1/4 36 22
BFX-250-T-BSP-CET-2"-A
BFX-250-T-BSP-CET-2"-B		 51 2"
1"1/2		 47
43		 27
24		 44 100 69.4 M 16X55
BFX-250-T-BSP-SID-2"-A 51 2" 47 27 44 100 68 M 14X50
BFX-250-T-BSP-SID-2"-B 1"1/2 43 24

(1)Pressure max. recommended
Flanges with 0'Ring and metric bolts.
For threaded NPT, replace T BSP by T NPT into the reference.
On request can be delivered with ISO 6164


PORT ASSEMBLY FLANGES FEMALE BSP/NPT THREAD CETOP-SIDERURGIE
PN 400* / CETOP
Part N° PN bar1 DN Ø F Ø A K L O GG Bolts
Metric
BFX-400-T-BSP-CET-3/8"-A
BFX-400-T-BSP-CET-3/8"-A		 400 10 3/8"
1/4"		 12
10		 13
12		 23 40 24.7 M 6X25
BFX-400-T-BSP-CET-1/2"-A 13 1/2" 14 15 32 45 29.7 M 8X35
BFX-400-T-BSP-CET-1/2"-B 3/8" 13 13
BFX-400-T-BSP-CET-3/4"-A
BFX-400-T-BSP-CET-3/4"-B		 19 3/4"
1/2"		 20
18		 18
15		 32 50 35.3 M 8X35
BFX-400-T-BSP-CET-1"-A 25 1" 25 18 36 65 43.8 M 10X40
BFX-400-T-BSP-CET-1"-B 3/4" 22 20
BFX-400-T-BSP-CET-1"1/4-A
BFX-400-T-BSP-CET-1"1/4-B		 32 1"1/4
1"		 32
28		 22
20		 38 75 51.6 M 12X45
BFX-400-T-BSP-CET-1"1/2-A 38 1"1/2 38 24 42 85 60 M 14X50
BFX-400-T-BSP-CET-1"1/2-B 1"1/4 36 22
BFX-400-T-BSP-CET-2"-A
BFX-400-T-BSP-CET-2"B		 51 2"
1"1/2		 47
43		 27
24		 44 100 69.4 M 16X55

(1)Pressure max. recommended
Flanges with 0'Ring and metric bolts.
For threaded NPT, replace T BSP by T NPT into the reference.
On request can be delivered with ISO 6164
+ -

PORT ASSEMBLY FLANGES SOCKET WELDING CETOP-SIDERURGIE
PN 250
Click to collapse
BRIDES DE FIXATION SOCKET WELDING INTEGRAL
PORT ASSEMBLY FLANGES SOCKET WELDING CETOP-SIDERURGIE
PN 250* / CETOP
Part N° PN bar1 DN Outer diameter tube Ø L1 Ø A K L O GG Bolts
Metric
MM GAZ SCHD
BFX-250-SWI-CET-1/2"-20.5
BFX-250-SWI-CET-1/2"-21.7		 250 13 20 21.25 21.34 20.5
21.7		 14 13 32 45 29.7 8 X 45
BFX-250-SWI-SID-1/2"-20.5
BFX-250-SWI-SID-1/2"-21.7		   20 21.25 21.34 20.5
21.7		 30 6 X 40
BFX-250-SWI-CET-SID-3/4"-25.5   19 25     25.5 19 14 32 50 35.3 8 X 45
BFX-250-SWI-CET-SID-3/4"-27.2     26.75 26.68 27.2
BFX-250-SWI-CET-SID-1"-30.5
BFX-250-SWI-CET-SID-1"-32.5
BFX-250-SWI-CET-SID-1"-34.5		   25 30
32		 33.50 33.40 30.5
32.5
34.5		 25 16 36 65 43.8 10 X 50
BFX-250-SWI-CET-SID-1"1/4-38.5     38     38.5            
BFX-250-SWI-CET-SID-1"1/4-40.7   32 40     40.7 31 18 38 75 51.6 12 X 60
BFX-250-SWI-CET-SID-1"1/4-42.8     42 42.25 42.16 42.8            
BFX-250-SWI-CET-1"1/2-48.6
BFX-250-SWI-CET-1"1/2-50.7		   38 50 48.25 48.26 48.6
50.7		 38 20 42 85 60 14 X 65
BFX-250-SWI-SID-1"1/2-48.6
BFX-250-SWI-SID-1"1/2-50.7		   50 48.25 48.26 48.6
50.7		 12 X 65
BFX-250-SWI-CET-2"-61   51 60 60.30 60.32 61 50 22 44 100 69.4 16 X 70
BFX-250-SWI-CET-2"-65.8   64     64
BFX-250-SWI-SID-2"-61   60     61.0 68 14 X 70
BFX-250-SWI-SID-2"-65.8   64     64
BFX-250-SWI-CET-2"1/2-74
BFX-250-SWI-CET-2"1/2-77
BFX-250-SWI-CET-2"1/2-81		   56 80 76.10 73.02 74.0
77.0
81.0		 63 24 48 120 83.4 20 X 80
BFX-250-SWI-SID-2"1/2-74
BFX-250-SWI-SID-2"1/2-77
BFX-250-SWI-SID-2"1/2-81		   80 76.10 73.02 74.0
77.0
81.0		 63 24 48 120 85 18 X 80
BFX-250-SWI-CET-3"-91   63 90   88.90 91.0 76 28 55 140 102.5 20 X 90
BFX-250-SWI-SID-3"-91   90   88.90 91.0 95 22 X 90

(1)Pressure max. recommended
Flanges with 0'Ring and metric bolts.
On request can be delivered with ISO 6164
+ -

90° PORT ASSEMBLY FLANGES BW CETOP-SIDERURGIE
PN250 / PN400
Click to collapse
BRIDES DE FIXATION BWI CETOP SIDERURGIE COUDEES 90
90° PORT ASSEMBLY FLANGES BW CETOP-SIDERURGIE
PN 250* / CETOP
Part N° PN bar1 DN Ø B D Ø A Ø H1 C O GG Bolts
Metric
BFX-90°-250-BWI-CET-3/8" 250 10 12 12 12.5 18 32 40 24.7 6 X30
BFX-90°-250-BWI-CET-1/2" 13 14 17 15 22 40 45 29.7 8 X 40
BFX-90°-250-BWI-SID-1/2" 13 14 17 15 22 40 45 30 6 X 40
BFX-90°-250-BWI-CET-SID-3/4"
BFX-90°-250-BWI-CET-SID-1"		 19
25		 19
23		 19
24		 20
25		 28
35		 42
50		 50
65		 35.3
43.8		 8 X 45
10 X 55
BFX-90°-250-BWI-CET-SID-1"1/4 32 30 30 32 44 56 75 51.6 12 X 70
BFX-90°-250-BWI-CET-1"1/2
BFX-90°-250-BWI-SID-1"1/2		 38
38		 35
35		 34
34		 38
38		 50
50		 65
65		 85
85		 60
60		 14 X 80
12 X 80
BFX-90°-250-BWI-CET-2" 51 43 42 47 63 75 100 69.4 16 X 100
BFX-90°-250-BWI-SID-2" 51 43 42 47 63 75 100 68 14 X 100
BFX-90°-250-BWI-CET-2"1/2
BFX-90°-250-BWI-SID-2"1/2		 56
56		 53
53		 53
53		 58
58		 76
76		 85
85		 120
120		 83.4
85		 20 X 120
18 X 120
BFX-90°-250-BWI-CET-3" 63 65 59 70 90 100 140 102.5 20 X 140
BFX-90°-250-BWI-SID-3" 63 65 59 70 90 100 140 95 22 X 140

(1)Pressure max. recommended
Flanges with 0'Ring and metric bolts.
On request can be delivered with ISO 6164


90° PORT ASSEMBLY FLANGES BW CETOP-SIDERURGIE
PN 400* / CETOP
Part N° PN bar1 DN Ø B D Ø A Ø H1 C O GG Bolts
Metric
BFX-90°-400-BWI-CET-3/8"
BFX-90°-400-BWI-CET-1/2"		 400 10
13		 12
14		 12
17		 12.5
15		 18
22		 32
40		 40
45		 24.7
29.7		 6 X 30
8 X 40
BFX-90°-400-BWI-CET-3/4"   19 19 19 20 28 42 50 35.3 8 X 45
BFX-90°-400-BWI-CET-1"
BFX-90°-400-BWI-CET-1"1/4		   25
32		 23
30		 24
30		 25
32		 35
44		 50
56		 65
75		 43.8
51.6		 10 X 55
12 X 70
BFX-90°-400-BWI-CET-1"1/2   38 32 34 38 51 65 85 60 14 X 80
BFX-90°-400-BWI-CET-2"
BFX-90°-400-BWI-CET-2"1/2		   51
56		 38
48		 42
53		 47
58		 63
80		 75
85		 100
120		 69.4
83.4		 16 X 100
20 X 120
BFX-90°-400-BWI-CET-3"   63 58 59 58 90 100 140 102.5 20 X140

(1)Pressure max. recommended
Flanges with 0'Ring and metric bolts.
On request can be delivered with ISO 6164
+ -

«T» BLOCKS BW CETOP-SIDERURGIE
PN250 / PN400
Click to collapse
BRIDES DE FIXATION BWI CETOP SIDERURGIE EN T
«T» BLOCKS BW CETOP-SIDERURGIE
PN 250* / CETOP
Part N° PN bar1 DN Ø B D Ø A Ø H1 C O GG Bolts
Metric
BFX-TE-250-BWI-CET-3/8" 250 10 12 12 12 18 32 40 24.7 6 X 30
BFX-TE-250-BWI-CET-1/2" 13 14 17 15 22 40 45 29.7 8 X 40
BFX-TE-250-BWI-SID-1/2" 13 14 17 15 22 40 45 30 6 X40
BFX-TE-250-BWI-CET-SID-3/4"
BFX-TE-250-BWI-CET-SID-1"		 19
25		 19
23		 19
24		 20
25		 28
35		 42
50		 50
65		 35.3
43.8		 8 X 45
10 X 55
BFX-TE-250-BWI-CET-SID-1"1/4 32 30 30 32 44 56 75 51.6 12 X 70
BFX-TE-250-BWI-CET-1"1/2
BFX-TE-250-BWI-SID-1"1/2		 38
38		 35
35		 34
34		 38
38		 50
50		 65
65		 85
85		 60
60		 14 X 80
12 X 80
BFX-TE-250-BWI-CET-2" 51 43 42 47 62 75 100 69.4 16 X 100
BFX-TE-250-BWI-SID-2" 51 43 42 47 62 75 100 68 14 X 100
BFX-TE-250-BWI-CET-2"1/2
BFX-TE-250-BWI-SID-2"1/2		 56
56		 53
53		 53
53		 58
58		 76
76		 85
85		 120
120		 83.4
85		 20 X 120
18 X 120
BFX-TE-250-BWI-CET-3" 63 65 59 70 90 100 140 102.5 20 X 140
BFX-TE-250-BWI-SID-3" 63 65 59 70 90 100 140 95 22 X 140

(1)Pressure max. recommended
Flanges with 0'Ring and metric bolts.
On request can be delivered with ISO 6164


«T» BLOCKS BW CETOP-SIDERURGIE
PN 400* / CETOP
Part N° PN bar1 DN Ø B D Ø A Ø H1 C O GG Bolts
Metric
BFX-TE-400-BWI-CET-3/8"
BFX-TE-400-BWI-CET-1/2"		 400 10
13		 12
14		 12
17		 12
14		 18
22		 32
40		 40
45		 24.7
29.7		 6 X 30
8 X 40
BFX-TE-400-BWI-CET-3/4" 19 19 19 18 28 42 50 35.3 8 X 45
BFX-TE-400-BWI-CET-1"
BFX-TE-400-BWI-CET-1"1/4		 25
32		 23
30		 24
30		 22
29		 35
44		 50
56		 65
75		 43.8
51.6		 10 X 55
12 X 70
BFX-TE-400-BWI-CET-1"1/2 38 32 34 35 51 65 85 60 14 X 80
BFX-TE-400-BWI-CET-2"
BFX-TE-400-BWI-CET-2"1/2		 51
56		 38
48		 42
53		 43
53		 63
80		 75
85		 100
120		 69.4
83.4		 16 X 100
20 X 120
BFX-TE-400-BWI-CET-3" 63 58 59 56 90 100 140 102.5 20 X 140

(1)Pressure max. recommended
Flanges with 0'Ring and metric bolts.
On request can be delivered with ISO 6164

Test port square

BRIDES PRISES DE PRESSION
TEST PORT SQUARE FLANGES CETOP-SIDERURGIE
PN 250* / CETOP
Part N° PN bar1 DN Ø A L GG FF Ø V
BM-250-CET/SID-PRISE-TEST-XX-3/8"
BM-250-CET-PRISE-TEST-XX-1/2"
BM-250-SID-PRISE-TEST-XX-1/2"		 250 10
13		 12
15
15		 20
29.7		 24.7
30		 40
45		 6.5
6.5 ou 8.5
BM-250-CET/SID-PRISE-TEST-XX-3/4" 19 20 30 35.3 50 8.5
BM-250-CET/SID-PRISE-TEST-XX-1"
BM-250-CET/SID-PRISE-TEST-XX-1"1/4		 25
32		 25
32		 30
35		 43.8
51.6		 65
75		 11
13
BM-250-CET-PRISE-TEST-XX-1"1/2
BM-250-SID-PRISE-TEST-XX-1"1/2		 38 38 35 60 85 13 ou 15
BM-250-CET-PRISE-TEST-XX-2"
BM-250-SID-PRISE-TEST-XX-2"		 51 47 40 69.4
68		 100 15 ou 17
BM-250-CET-PRISE-TEST-XX-2"1/2
BM-250-SID-PRISE-TEST-XX-2"1/2		 56 58 40 83.4
85		 120 19 ou 21
BM-250-CET-PRISE-TEST-XX-3"
BM-250-SID-PRISE-TEST-XX-3"		 63 77 45 102.5
95		 140 21 ou 23

These flange bodies are fitted with pressure inlets with M 10X100 A shape sealed layout
- G 1/4 on request
- Galvanized-bichromated.


TEST PORT SQUARE FLANGES CETOP-SIDERURGIE
PN 400* / CETOP
Part N° PN bar1 DN Ø A L GG FF Ø V
BM-400-CET-PRISE-TEST-XX-3/8"
BM-400-CET-PRISE-TEST-XX-1/2"		 400 10
13		 11
13		 20
25		 24.7
29.7		 40
45		 6.5
8.5
BM-400-CET-PRISE-TEST-XX-3/4" 19 17.5 30 35.3 50 8.5
BM-400-CET-PRISE-TEST-XX-1"
BM-400-CET-PRISE-TEST-XX-1"1/4		 25
32		 22
29		 30
35		 43.8
51.6		 65
75		 11
13
BM-400-CET-PRISE-TEST-XX-1"1/2 38 35 35 60 85 15
BM-400-CET-PRISE-TEST-XX-2"
BM-400-CET-PRISE-TEST-XX-2"1/2		 51
56		 43
53		 46
56		 69.4
83.4		 100
120		 17
21
BM-400-CET-PRISE-TEST-XX-3" 63 58 60 102.5 140 21

These flange bodies are fitted with pressure inlets with G 1/4 B shape sealed layout and they are galvanized-bichromated

Union assembly

+ -

UNION ASSEMBLY FLANGES REDUCING SOCKET WELDING CETOP-SIDERURGIE
PN250 / PN400
Click to collapse
BRIDES DE LIAISON BUTT WELDING PASSAGE REDUIT CETOP SIDERURGIE
UNION ASSEMBLY FLANGES REDUCING SOCKET WELDING CETOP-SIDERURGIE
PN 250* / CETOP
Part N° PN
bar1		 DN For tube
diameter to .... at ....		 Ø A Ø H1 L O GG Bolts
Metric
BL-250-BWR-CET-1/2"
BL-250-BWR-SID-1/2"		 250 13
13		 14 - 18
14 - 18		 12
12		 17.5
18		 90
90		 45
45		 29.7
30		 8 X 45
6 X40
BL-250-BWR-CET-SID-3/4" 19 18 - 22 13 22 100 50 35.3 8 X 45
BL-250-BWR-CET-SID-1"
BL-250-BWR-CET-SID-1"1/4		 25
32		 25 - 28
30 - 35		 20
25		 28
35		 110
120		 65
75		 43.8
51.6		 10 X 50
12 X 60
BL-250-BWR-CET-1"1/2 38 38 - 43 32 43 130 85 60 14 X 70
BL-250-BWR-SID-1"1/2 38 38 - 43 32 43 130 85 60 12 X 70
BL-250-BWR-CET-2"
BL-250-BWR-SID-2"		 51
51		 48 - 50
48 - 50		 38
38		 50
50		 140
140		 100
100		 69.4
68		 16 X 75
14 X 75
BL-250-BWR-CET-2"1/2 56 60 - 63 47 62 150 120 83.4 18 X 100
BL-250-BWR-SID-2"1/2 56 60 - 63 47 62 150 120 85 20 X 100
BL-250-BWR-CET-3"
BL-250-BWR-CET-3"1/2		 63
70		 73 - 76
88 - 90		 56
70		 76
90		 70
180		 140
140		 102.5
102.5		 20 X 110
20 X 130
BL-250-BWR-CET-4" 80 95 - 102 80 102 200 160 113.2 24 X 150
BL-250-BWR-SID-4" 80 95 - 102 80 102 200 180 130 27 X 150

(1)Pression maxi. recommandée
Flanges with 0'Ring and metric bolts.
On request can be delivered with ISO 6164.


UNION ASSEMBLY FLANGES REDUCING SOCKET WELDING CETOP-SIDERURGIE
PN 400* / CETOP
Part N° PN
bar1		 DN For tube
diameter to .... at ....		 Ø A Ø H1 L O GG Bolts
Metric
BL-400-BWR-CET-1/2"
BL-400-BWR-CET-3/4"		 400 13
19		 16 - 18
20 - 22		 12
13		 17.5
22		 90
100		 45
50		 29.7
35.3		 8 X 45
8 X 55
BL-400-BWR-CET-1" 25 25 - 28 17.5 28 110 65 43.8 10 X 60
BL-400-BWR-CET-1"1/4
BL-400-BWR-CET-1"1/2		 32
38		 30 - 35
38 - 43		 22
29		 35
43.8		 120
130		 75
85		 51.6
60		 12 X 70
14 X 80
BL-400-BWR-CET-2" 51 48 - 51 35 51 130 100 69.4 16 X 100
BL-400-BWR-CET-2"1/2
BL-400-BWR-CET-3"		 56
63		 60 - 65
73 - 76		 43
53		 65
80		 140
180		 120
140		 83.4
102.5		 20 X 120
20 X 130
BL-400-BWR-CET-3"1/2 70 88 - 90 58 90 180 140 102.5 20 X 140
BL-400-BWR-CET-4" 80 95 - 102 63 102 220 160 113.2 24 X 150

(1)Pression maxi. recommandée
Flanges with 0'Ring and metric bolts.
On request can be delivered with ISO 6164.
+ -

UNION ASSEMBLY FLANGES BUTT WELDING CET/SID
PN250 / PN400
Click to collapse
BRIDES DE LIAISON BUTT WELDING INTEGRAL CETOP SIDERURGIE
UNION ASSEMBLY FLANGES BUTT WELDING CETOP-SIDERURGIE
PN 250* / CETOP
Part N° PN bar1 DN For tube
diameter to .... at ....		 Ø A Ø H1 L O GG Bolts
Metric
BL-250-BWI-CET-3/8" 250 10 14 - 18 12 18 80 40 24.7 6 X 35
BL-250-BWI-CET-1/2" 13 18 - 22 13 22 90 45 29.7 8 X 45
BL-250-BWI-SID-1/2" 13 18 - 22 13 22 90 45 30 6 X 40
BL-250-BWI-CET-SID-3/4"
BL-250-BWI-CET-SID-1"		 19
25		 25 - 28
30 - 35		 19
25		 28
35		 100
110		 50
65		 35.3
43.8		 8 X 45
10 X 50
BL-250-BWI-CET-SID-1"1/4 32 38 - 43 32 43 120 75 51.6 12 X 60
BL-250-BWI-CET-1"1/2
BL-250-BWI-SID-1"1/2		 38
38		 48 - 50
48 - 50		 38
38		 50
50		 130
130		 85
85		 60
60		 14 X 70
12 X 70
BL-250-BWI-CET-2" 51 60 - 63 47 62 140 100 69.4 16 X 75
BL-250-BWI-SID-2" 51 60 - 63 47 62 140 100 68 14 X 75
BL-250-BWI-CET-2"1/2
BL-250-BWI-SID-2"1/2		 56
56		 73 - 80
73 - 80		 58
58		 76
76		 150
150		 120
120		 83.4
85		 20 X 100
18 X 100
BL-250-BWI-CET-3" 63 88 - 90 70 90 170 140 102.5 20 X 110
BL-250-BWI-SID-3" 63 88 - 90 70 90 170 140 95 22 X 110
BL-250-BWI-CET-3"1/2
BL-250-BWI-CET-4"
BL-250-BWI-SID-4"		 70
80
80		 95 - 102
113-120
113-120		 77
90
90		 102
118
118		 180
200
200		 140
160
180		 102.5
113.2
130		 20 X 130
24 X 150
27 X 150

(1)Pression maxi. recommandée
Flanges with 0'Ring and metric bolts.
On request can be delivered with ISO 6164.


UNION ASSEMBLY FLANGES BUTT WELDING CETOP-SIDERURGIE
PN 400* / CETOP
Part N° PN bar1 DN For tube
diameter to .... at ....		 Ø A Ø H1 L O GG Bolts
Metric
BL-400-BWI-CET-3/8"
BL-400-BWI-CET- 1/2"		 400 10
13		 16 - 18
20 - 22		 11
13		 17.5
22		 80
90		 40
45		 24.7
29.7		 6 X 45
8 X 50
BL-400-BWI-CET-3/4" 19 25 - 28 17.5 28 100 50 35.3 8 X 55
BL-400-BWI-CET-1"
BL-400-BWI-CET-1"1/4		 25
32		 33 - 35
42 - 45		 22
29		 35
43.8		 110
120		 65
75		 43.8
51.6		 10 X 60
12 X 70
BL-400-BWI-CET-1"1/2 38 48 - 51 35 50.6 130 85 60 14 X 80
BL-400-BWI-CET-2"
BL-400-BWI-CET-2"1/2		 51
56		 60 - 65
75 - 80		 43
53		 65
76		 140
160		 100
120		 69.4
83.4		 16 X 100
20 X 120
BL-400-BWI-CET-3" 63 88 - 90 58 90 180 140 102.5 20 X 130
BL-400-BWI-CET-3"1/2
BL-400-BWI-CET-4"		 70
80		 90 - 102
110 - 120		 63
74		 102
114		 180
220		 140
160		 102.5
113.2		 20 X 140
24 X 150

(1)Pression maxi. recommandée
Flanges with 0'Ring and metric bolts.
On request can be delivered with ISO 6164.
+ -

UNION ASSEMBLY FLANGES "T" BW CETOP-SIDERURGIE
PN250 / PN400
Click to collapse
BRIDES DE LIAISON BWI CETOP SIDERURGIE EN T
UNION ASSEMBLY FLANGES "T" BW CETOP-SIDERURGIE
PN 250* / CETOP
Part N° PN bar1 DN C Ø A Ø H1 S** O GG Bolts
Metric
BL-TE-250-BWI-CET-3/8" 250 10 32 12.5 18 52 40 24.7 6 X 40
BL-TE-250-BWI-CET-1/2" 13 40 13 22 62 45 29.7 8 X 50
BL-TE-250-BWI-SID-1/2" 13 40 13 22 62 45 30 6 X 50
BL-TE-250-BWI-CET-SID-3/4"
BL-TE-250-BWI-CET-SID-1"		 19
25		 42
50		 19
25		 28
35		 69
79		 50
65		 35.3
43.8		 8 X 55
10 X 70
BL-TE-250-BWI-CET-SID-1"1/4 32 56 32 43 90 75 51.6 12 X 90
BL-TE-250-BWI-CET-1"1/2
BL-TE-250-BWI-SID-1"1/2		 38
38		 65
65		 38
38		 50
50		 99
99		 85
85		 60
60		 14 X 100
12 X 100
BL-TE-250-BWI-CET-2" 51 75 47 62 112 100 69.4 16 X 120
BL-TE-250-BWI-SID-2" 51 75 47 62 112 100 68 14 X 120
BL-TE-250-BWI-CET-2"1/2
BL-TE-250-BWI-SID-2"1/2		 56
56		 85
85		 58
58		 76
76		 128
128		 120
120		 83.4
85		 20 X 150
18 X 150
BL-TE-250-BWI-CET-3" 63 100 70 90 144 140 102.5 20 X 160
BL-TE-250-BWI-SID-3" 63 100 70 90 144 140 95 22 X 170

(1)Pression maxi. recommandée
Flanges with 0'Ring and metric bolts.
On request can be delivered with ISO 6164.


UNION ASSEMBLY FLANGES "T" BW CETOP-SIDERURGIE
PN 400* / CETOP
Part N° PN bar1 DN C Ø A Ø H1 S** O GG Bolts
Metric
BL-TE-400-BWI-CET-3/8"
BL-TE-400-BWI-CET-1/2"		 400 10
13		 32
40		 11
13		 18
22		 52
62		 40
45		 24.7
29.7		 6 X 45
8 X 55
BL-TE-400-BWI-CET-3/4" 19 42 17.5 28 69 50 35.3 8 X 60
BL-TE-400-BWI-CET-1"
BL-TE-400-BWI-CET-1"1/4		 25
32		 50
56		 22
29		 35
44		 79
90		 65
75		 43.8
51.6		 10 X 70
12 X 90
BL-TE-400-BWI-CET-1"1/2 38 65 35 51 99 85 60 14 X 100
BL-TE-400-BWI-CET-2"
BL-TE-400-BWI-CET-2"1/2		 51
56		 75
85		 43
53		 61
80		 112
133		 100
120		 69.4
83.4		 16 X 130
20 X 150
BL-TE-400-BWI-CET-3" 63 100 58 90 149 140 102.5 20 X 180

(1)Pression maxi. recommandée
Flanges with 0'Ring and metric bolts.
On request can be delivered with ISO 6164.

Blank flanges

+ -

BLANK FLANGES CETOP-SIDERURGIE
2 PARTS
PN250 / PN400
Click to collapse
BRIDES OBTURATION EN DEUX PARTIES CETOP SIDERURGIE
BLANK FLANGES CETOP-SIDERURGIE 2 PARTS
PN 250* / CETOP
Part N° PN bar1 DN L O GG Bolts
Metric
BFX-OB-250-CET-3/8"
BFX-OB-250-CET-1/2"
BFX-OB-250-SID-1/2"		 250 10
13
13		 15
16
16		 40
45
45		 24.7
29.7
30		 6 X 25
8 X 30
6 X 25
BFX-OB-250-CET-SID-3/4" 19 16 50 35.3 8 X 30
BFX-OB-250-CET-SID-1"
BFX-OB-250-CET-SID-1"1/4		 25
32		 18
18		 65
75		 43.8
51.6		 10 X 35
12 X 45
BFX-OB-250-CET-1"1/2 38 18 85 60 14 X 50
BFX-OB-250-SID-1"1/2 38 21 85 60 12 X 50
BFX-OB-250-CET-2"
BFX-OB-250-SID-2"		 51
51		 21
21		 100
100		 69.4
68.0		 16 X 55
14 X 50
BFX-OB-250-CET-2"1/2 56 21 120 83.4 20 X 70
BFX-OB-250-SID-2"1/2 56 21 120 85 18 X 65
BFX-OB-250-CET-3"
BFX-OB-250-SID-3"		 63
63		 24
24		 140
140		 102.5
95		 20 X 75
22 X 75
BFX-OB-250-CET-3"1/2 70 45 140 102.5 20 X 90
BFX-OB-250-CET-4"
BFX-OB-250-SID-4"		 80
80		 55
55		 160
180		 113.2
130		 24 X 100
27 X 100

(1)Pressure max. recommended
Flanges with 0'Ring and metric bolts.
On request can be delivered with ISO 6164


BLANK FLANGES CETOP-SIDERURGIE 2 PARTS
PN 400* / CETOP
Part N° PN bar1 DN L O GG Bolts
Metric
BFX-OB-400-CET-3/8"
BFX-OB-400-CET-1/2"		 400 10
13		 18
19		 40
45		 24.7
29.7		 6 X 25
8 X 30
BFX-OB-400-CET-3/4" 19 21 50 35.3 8 X 35
BFX-OB-400-CET-1"
BFX-OB-400-CET-1"1/4		 25
32		 26
31		 65
75		 43.8
51.6		 10 X 40
12 X 45
BFX-OB-400-CET-1"1/2 38 34 85 60.0 14 X 55
BFX-OB-400-CET-2"
BFX-OB-400-CET-2"1/2		 51
56		 42
47		 100
120		 69.4
83.4		 16 X 65
20 X 80
BFX-OB-400-CET-3" 63 54 140 102.5 20 X 90
BFX-OB-400-CET-3"1/2
BFX-OB-400-CET-4"		 70
80		 54
61		 140
160		 102.5
113.2		 20 X 90
24 X 100

(1)Pressure max. recommended
Flanges with 0'Ring and metric bolts.
On request can be delivered with ISO 6164
+ -

BLANK FLANGES CETOP-SIDERURGIE
MONOBlOC
PN250 / PN400
Click to collapse
BRIDES OBTURATION MONOBLOC CETOP SIDERURGIE
BLANK FLANGES CETOP-SIDERURGIE MONOBlOC
PN 250* / CETOP
Part N° PN bar1 DN L O GG C Ø B** D Bolts
Metric
BFX-OB-MONO-250-CET-3/8"
BFX-OB-MONO-250-CET-1/2"
BFX-OB-MONO-250-SID-1/2"		 250 10
13
13		 23
32
32		 40
45
45		 24.7
29.7
30		 16
23
23		 12
14
14		 7
9
7		 6 X 25
8 X 35
6 X 30
BFX-OB-MONO-250-CET-SID-3/4" 19 32 50 35.3 23 19 9 8 X 35
BFX-OB-MONO-250-CET-SID-1"
BFX-OB-MONO-250-CET-SID-1"1/4		 25
32		 35
38		 65
75		 43.8
51.6		 24
25		 25
31		 11
13		 10 X 40
12 X 45
BFX-OB-MONO-250-CET-1"1/2 38 42 85 60 27 36 15 14 X 50
BFX-OB-MONO-250-SID-1"1/2 38 42 85 60 27 36 13 12 X 50
BFX-OB-MONO-250-CET-2"
BFX-OB-MONO-250-SID-2"		 51
51		 44
44		 100
100		 69.4
68		 27
27		 45
45		 17
15		 16 X 55
14 X 50
BFX-OB-MONO-250-CET-2"1/2 56 55 120 83.4 34 58 21 20 X 70
BFX-OB-MONO-250-SID-2"1/2 56 55 120 85 34 58 19 18 X 70
BFX-OB-MONO-250-CET-3"
BFX-OB-MONO-250-SID-3"		 63
63		 60
60		 140
140		 102.5
95		 37
37		 70
70		 21
23		 20 X 70
22 X 70

(1)Pressure max. recommended
Flanges with 0'Ring and metric bolts.
On request can be delivered with ISO 6164


BLANK FLANGES CETOP-SIDERURGIE MONOBlOC
PN 400* / CETOP
Part N° PN bar1 DN L O GG C Ø B** D Bolts
Metric
BFX-OB-MONO-400-CET-3/8"
BFX-OB-MONO-400-CET-1/2"		 400 10
13		 23
32		 40
45		 24.7
29.7		 16
23		 12
14		 7
9		 6 X 25
8 X 35
BFX-OB-MONO-400-CET-3/4" 19 32 50 35.3 23 19 9 8 X 35
BFX-OB-MONO-400-CET-1"
BFX-OB-MONO-400-CET-1"1/4		 25
32		 35
38		 65
75		 43.8
51.6		 24
25		 25
31		 11
13		 10 X 40
12 X 45
BFX-OB-MONO-400-CET-1"1/2 38 42 85 60 27 36 15 14 X 50
BFX-OB-MONO-400-CET-2"
BFX-OB-MONO-400-CET-2"1/2		 51
56		 44
55		 100
120		 69.4
83.4		 27
34		 45
58		 17
21		 16 X 55
20 X 70
BFX-OB-MONO-400-CET-3" 63 60 140 102.5 37 70 21 20 X 70

(1)Pressure max. recommended
Flanges with 0'Ring and metric bolts.
On request can be delivered with ISO 6164

Conter flanges

+ -

CONTER FLANGES FEMALE BSP/NPT THREAD CETOP-SIDERURGIE
PN250 / PN400
Click to collapse
BRIDES SANS GORGE TARAUDEES BSP NPT
CONTER FLANGES FEMALE BSP/NPT THREAD CET/SID
PN 250* / CETOP
Part N° PN bar1 DN Ø F Ø A K L O GG Bolts
BAS-250-T-BSP-CET-3/8"-A
BAS-250-T-BSP-CET-3/8"-B		 250 10 3/8"
1/4"		 12
10		 13
12		 23 40 24.7 M 6
BAS-250-T-BSP-CET-1/2"-A 13 1/2" 14 15 32 45 29.7 M 8
BAS-250-T-BSP-CET-1/2"-B 3/8" 13 13
BAS-250-T-BSP-SID-1/2"-A 1/2" 14 15 32 45 30 M 6
BAS-250-T-BSP-SID-1/2"-B 3/8" 13 13
BAS-250-T-BSP-CET-3/4"-A
BAS-250-T-BSP-CET-3/4"-B		 19 3/4"
1/2"		 20
18		 18
15		 32 50 35.3 M 8
BAS-250-T-BSP-CET/SID-1"-A 25 1" 25 20 36 65 43.8 M 10
BAS-250-T-BSP-CET/SID-1"-B 3/4 22 18
BAS-250-T-BSP-CET/SID-1"1/4-A
BAS-250-T-BSP-CET/SID-1"1/4-B		 32 1"1/4
1"		 32
28		 22
20		 38 75 51.6 M 12
BAS-250-T-BSP-CET-1"1/2-A 38 1"1/2 38 24 42 85 60 M 14
BAS-250-T-BSP-CET-1"1/2-B 1"1/4 36 22
BAS-250-T-BSP-SID-1"1/2-A 1"1/2 38 24 42 85 60 M 12
BAS-250-T-BSP-SID-1"1/2-B 1"1/4 36 22
BAS-250-T-BSP-CET-2"-A
BAS-250-T-BSP-CET-2"-B		 51 2"
1"1/2		 47
43		 27
24		 44 100 69.4 M 16
BAS-250-T-BSP-SID-2"-A
BAS-250-T-BSP-SID-2"-B		 2"
1"1/2		 47
43		 27
24		 44 100 68 M 14

(1)Pressure max. recommended
For threaded NPT, replace T BSP by T NPT into the reference
* On request can be delivered with ISO 6164


CONTER FLANGES FEMALE BSP/NPT THREAD CET/SID
PN 400* / CETOP
Part N° PN bar1 DN Ø F Ø A K L O GG Bolts
BAS-400-T-BSP-CET-3/8"-A
BAS-400-T-BSP-CET-3/8"-B		 400 10 3/8"
1/4"		 12
10		 13
12		 23 40 24.7 M 6
BAS-400-T-BSP-CET-1/2"-A 13 1/2" 14 15 32 45 29.7 M 8
BAS-400-T-BSP-CET-1/2"-B 3/8" 13 13
BAS-400-T-BSP-CET-3/4"-A
BAS-400-T-BSP-CET-3/4"-B		 19 3/4"
1/2"		 20
18		 18
15		 32 50 35.3 M 8
BAS-400-T-BSP-CET-1"-A 25 1" 25 20 36 65 43.8 M 10
BAS-400-T-BSP-CET-1"-B 3/4 22 18
BAS-400-T-BSP-CET-1"1/4-A
BAS-400-T-BSP-CET-1"1/4-B		 32 1"1/4
1"		 32
28		 22
20		 38 75 51.6 M 12
BAS-400-T-BSP-CET-1"1/2-A 38 1"1/2 38 24 42 85 60 M 14
BAS-400-T-BSP-CET-1"1/2-B 1"1/4 36 22
BAS-400-T-BSP-CET-2"-A
BAS-400-T-BSP-CET-2"-B		 51 2"
1"1/2		 47
43		 27
24		 44 100 69.4 M 16

(1)Pressure max. recommended
For threaded NPT, replace T BSP by T NPT into the reference
* On request can be delivered with ISO 6164
+ -

COUNTER FLANGES SOCKET WELDING CETOP-SIDERURGIE
PN250
Click to collapse
BRIDES A SOUDER SANS GORGE SOCKET WELDING INTEGRAL
COUNTER FLANGES SOCKET WELDING CET/SID
PN 250* / CETOP
Part N° PN
bar1		 DN Outer diameter tube Ø L1 Ø A K L O GG Bolts
MM GAZ SCHD
BAS-250-SWI-CET-1/2"-20.5
BAS-250-SWI-CET-1/2"-21.7
BAS-250-SWI-SID-1/2"-20.5
BAS-250-SWI-SID-1/2"-21.7		 250 13 20
20		 21.25
21.25		 21.34
21.34		 20.5
21.7
20.5
21.7		 14 13 32 45 29.7
30		 M 8
M 6
BAS-250-SWI-CET/SID-3/4"-25.5
BAS-250-SWI-CET/SID-3/4"-27.2		 19 25 26.75 26.68 25.5
27.2		 19 14 32 50 35.3 M 8
BAS-250-SWI-CET/SID-1"-30.5
BAS-250-SWI-CET/SID-1"-32.5
BAS-250-SWI-CET/SID-1"-34.5		 25 30
32		 33.5 33.4 30.5
32.5
34.5		 25 16 36 65 43.8 M 10
BAS-250-SWI-CET/SID-1"1/4-38.5
BAS-250-SWI-CET/SID-1"1/4-40.7
BAS-250-SWI-CET/SID-1"1/4-42.8		 32 38
40
42		 42.25 42.16 38.5
40.7
42.8		 31 18 38 75 51.6 M 12
BAS-250-SWI-CET-1"1/2-48.6
BAS-250-SWI-CET-1"1/2-50.7
BAS-250-SWI-SID-1"1/2-48.6
BAS-250-SWI-SID-1"1/2-50.7		 38 50
50		 48.25
48.25		 48.26
48.26		 48.6
50.7
48.6
50.7		 38 20 42 85 60 M 14
M 12
BAS-250-SWI-CET-2"-61
BAS-250-SWI-CET-2"-64
BAS-250-SWI-SID-2"-61
BAS-250-SWI-SID-2"-64		 51 60
64
60
64		 60.3
60.3		 60.32
60.32		 61
64
61
64		 50 22 44 100 69.4
68		 M 16
M 14
BAS-250-SWI-CET-2"1/2-74
BAS-250-SWI-CET-2"1/2-77
BAS-250-SWI-CET-2"1/2-81
BAS-250-SWI-SID-2"1/2-74
BAS-250-SWI-SID-2"1/2-77
BAS-250-SWI-SID-2"1/2-81		 56 80
80		 76.1
76.1		 73.02
73.02		 74
77
81
74
77
81		 63 24 48 120 83.4
85		 M 20
M 18
BAS-250-SWI-CET-3"-91 63 90
 		 88.9 91 76 28 55 140 102.5 M 20
BAS-250-SWI-SID-3"-91 95 M 22

(1)Pressure max. recommended
On request can be delivered with ISO 6164

Blocks

+ -

PORT ELBOW CETOP-SIDERURGIE
PN250 / PN400
Click to collapse
BLOCS EQUERRES DE FIXATION
PORT ELBOW CETOP-SIDERURGIE
PN 250* / CETOP
Part N° PN bar1 DN Ø A O C GG Bolts
BLC-EQ-FIX-250-CET-3/8"
BLC-EQ-FIX-250-CET-1/2"
BLC-EQ-FIX-250-SID-1/2"		 250 10
13
13		 11
13
13		 40
45
45		 55
60
60		 24.7
29.7
30		 M 6 X 50
M 8 X 60
M 6 X 55
BLC-EQ-FIX-250-CET-SID-3/4" 19 19 50 70 35.3 M 8 X 65
BLC-EQ-FIX-250-CET-SID-1"
BLC-EQ-FIX-250-CET-SID-1"1/4		 25
32		 25
32		 65
75		 85
100		 43.8
51.6		 M 10 X 80
M 12 X 90
BLC-EQ-FIX-250-CET-1"1/2 38 38 85 115 60 M 14 X 110
BLC-EQ-FIX-250-SID-1"1/2 38 38 85 115 60 M 12 X 100
BLC-EQ-FIX-250-CET-2"
BLC-EQ-FIX-250-SID-2"		 51
51		 47
47		 100
100		 130
130		 69.4
68		 M 16 X 130
M 14 X 120
BLC-EQ-FIX-250-CET-2"1/2 56 58 120 170 83.4 M 20 X 150
BLC-EQ-FIX-250-SID-2"1/2 56 58 120 170 85 M 18 X 150
BLC-EQ-FIX-250-CET-3"
BLC-EQ-FIX-250-SID-3"		 63
63		 70
70		 140
140		 190
190		 102.5
95		 M 20 X 170
M 22 X 170

(1)Pressure max. recommended
Blocks with 0'Ring and metric bolts.
*On request can be delivered with ISO 6164


PORT ELBOW CETOP-SIDERURGIE
PN 400* / CETOP
Part N° PN bar1 DN Ø A O C GG Bolts
BLC-EQ-FIX-400-CET-3/8"
BLC-EQ-FIX-400-CET-1/2"		 400 10
13		 11
13		 40
45		 55
60		 24.7
29.7		 M 6 X 50
M 8 X 60
BLC-EQ-FIX-400-CET-3/4" 19 17.5 50 66 35.3 M 8 X 65
BLC-EQ-FIX-400-CET-1"
BLC-EQ-FIX-400-CET-1"1/4		 25
32		 22
29		 65
75		 80
95		 43.8
51.6		 M 10 X 80
M 12 X 100
BLC-EQ-FIX-400-CET-1"1/2 38 35 85 110 60 M 14 X 110
BLC-EQ-FIX-400-CET-2"
BLC-EQ-FIX-400-CET-2"1/2		 51
56		 43
53		 100
120		 125
150		 69.4
83.4		 M 16 X 130
M 20 X 150
BLC-EQ-FIX-400-CET-3" 63 58 140 170 102.5 M 20 X 170

(1)Pressure max. recommended
Blocks with 0'Ring and metric bolts.
*On request can be delivered with ISO 6164
+ -

"L" BLOCKS CETOP-SIDERURGIE
PN250 / PN400
Click to collapse
BLOCS DE DISTRIBUTION EN L
BLOCS DE DISTRIBUTION EN "L" CETOP-SIDÉRURGIE
PN 250* / CETOP
Part N° PN bar1 DN Ø A O C GG Bolts
BLC-DIST-L-250-CET-3/8"
BLC-DIST-L-250-CET-1/2"
BLC-DIST-L-250-SID-1/2"		 250 10
13
13		 11
13
13		 40
45
45		 55
60
60		 24.7
29.7
30		 M 6
M 8
M 6
BLC-DIST-L-250-CET/SID-3/4" 19 19 50 70 35.3 M 8
BLC-DIST-L-250-CET/SID-1"
BLC-DIST-L-250-CET/SID-1"1/4		 25
32		 25
32		 65
75		 85
100		 43.8
51.6		 M 10
M 12
BLC-DIST-L-250-CET-1"1/2 38 38 85 115 60 M 14
BLC-DIST-L-250-SID-1"1/2 38 38 85 115 60 M 12
BLC-DIST-L-250-CET-2"
BLC-DIST-L-250-SID-2"		 51
51		 47
47		 100
100		 130
130		 69.4
68		 M 16
M 14
BLC-DIST-L-250-CET-2"1/2 56 58 120 170 83.4 M 20
BLC-DIST-L-250-SID-2"1/2 56 58 120 170 85 M 18
BLC-DIST-L-250-CET-3"
BLC-DIST-L-250-SID-3"		 63
63		 70
70		 140
140		 190
190		 102.5
95		 M 20
M 22

(1)Pressure max. recommended
*On request can be delivered with ISO 6164


BLOCS DE DISTRIBUTION EN "L" CETOP-SIDÉRURGIE
PN 400* / CETOP
Part N° PN bar1 DN Ø A O C GG Bolts
BLC-DIST-L-400-CET-3/8"
BLC-DIST-L-400-CET-1/2"		 400 10
13		 11
13		 40
45		 55
60		 24.7
29.7		 M 6
M 8
BLC-DIST-L-400-CET-3/4" 19 17.5 50 66 35.3 M 8
BLC-DIST-L-400-CET-1"
BLC-DIST-L-400-CET-1"1/4		 25
32		 22
29		 65
75		 80
95		 43.8
51.6		 M 10
M 12
BLC-DIST-L-400-CET-1"1/2 38 35 85 110 60 M 14
BLC-DIST-L-400-CET-2"
BLC-DIST-L-400-CET-2"1/2		 51
56		 43
53		 100
120		 125
150		 69.4
83.4		 M 16
M 20
BLC-DIST-L-400-CET-3" 63 58 140 170 102.5 M 20

(1)Pressure max. recommended
*On request can be delivered with ISO 6164
+ -

"T BLOCKS CETOP-SIDERURGIE
PN250 / PN400
Click to collapse
BLOCS DE DISTRIBUTION EN T
"T BLOCKS CETOP-SIDERURGIE
PN 250* / CETOP
Part N° PN bar1 DN Ø A O C GG Bolts
BLC-DIST-T-250-CET-3/8"
BLC-DIST-T-250-CET-1/2"
BLC-DIST-T-250-SID-1/2"		 250 10
13
13		 11
13
13		 40
45
45		 55
60
60		 24.7
29.7
30		 M 6
M 8
M 6
BLC-DIST-T-250-CET/SID-3/4" 19 19 50 70 35.3 M 8
BLC-DIST-T-250-CET/SID-1"
BLC-DIST-T-250-CET/SID-1"1/4		 25
32		 25
32		 65
75		 85
100		 43.8
51.6		 M 10
M 12
BLC-DIST-T-250-CET-1"1/2 38 38 85 115 60 M 14
BLC-DIST-T-250-SID-1"1/2 38 38 85 115 60 M 12
BLC-DIST-T-250-CET-2"
BLC-DIST-T-250-SID-2"		 51
51		 47
47		 100
100		 130
130		 69.4
68		 M 16
M 14
BLC-DIST-T-250-CET-2"1/2 56 58 120 170 83.4 M 20
BLC-DIST-T-250-SID-2"1/2 56 58 120 170 85 M 18
BLC-DIST-T-250-CET-3"
BLC-DIST-T-250-SID-3"		 63
63		 70
70		 140
140		 190
190		 102.5
95		 M 20
M 22

(1)Pressure max. recommended
*On request can be delivered with ISO 6164
Blocks  «X» on request


"T BLOCKS CETOP-SIDERURGIE
PN 400* / CETOP
Part N° PN bar1 DN Ø A O C GG Bolts
BLC-DIST-T-400-CET-3/8"
BLC-DIST-T-400-CET-1/2"		 400 10
13		 11
13		 40
45		 55
60		 24.7
29.7		 M 6
M 8
BLC-DIST-T-400-CET-3/4" 19 17.5 50 66 35.3 M 8
BLC-DIST-T-400-CET-1"
BLC-DIST-T-400-CET-1"1/4		 25
32		 22
29		 65
75		 80
95		 43.8
51.6		 M 10
M 12
BLC-DIST-T-400-CET-1"1/2 38 35 85 110 60 M 14
BLC-DIST-T-400-CET-2"
BLC-DIST-T-400-CET-2"1/2		 51
56		 43
53		 100
120		 125
150		 69.4
83.4		 M 16
M 20
BLC-DIST-T-400-CET-3" 63 58 140 170 102.5 M 20

(1)Pressure max. recommended
*On request can be delivered with ISO 6164
Blocks  «X» on request

Accessories for flanges

Flanged Head

+ -

FLANGED HEAD SOCKET WELDING (SWI)
SAE 3000 / SAE 6000
Click to collapse
Collets socket welding a passage integral
FLANGED HEAD SOCKET WELDING (SWI)
ISO 6162-1 - S.A.E. 3000
Part N° DN Outer diameter tube Ø L1 Ø L2 Ø A K Ø C L
MM GAZ SCHD
CAG-3000-SWI-1/2"-20.5
CAG-3000-SWI-1/2"-21.7		 13 20 21.25 21.30 20.5
21.7		 30 13 13 30.5 60
CAG-3000-SWI-3/4"-25.5
CAG-3000-SWI-3/4"-27.3		 19 25 26.75 26.68 25.5
27.3		 35 19 13 38.4 68
CAG-3000-SWI-1"-30.5
CAG-3000-SWI-1"-32.5
CAG-3000-SWI-1"-34
CAG-3000-SWI-1"-35.5		 25 30
32
35		 33.50 33.40 30.5
32.5
34
35.5		 44 25 16 44.7 75
CAG-3000-SWI-1"1/4-38.5
CAG-3000-SWI-1"1/4-40.5
CAG-3000-SWI-1"1/4-43		 32 38
40
42		 42.25 42.16 38.5
40.5
43		 55 32 18 51.1 95
CAG-3000-SWI-1"1/2-49
CAG-3000-SWI-1"1/2-50.4		 38 48
50		 48.25 48.26 49
50.4		 63 38 20 60.6 100
CAG-3000-SWI-2"-61
CAG-3000-SWI-2"-65.8		 51 60
65		 60.3 60.32 61
65.8		 79 47 22 71.4 107
CAG-3000-SWI-2"1/2-74
CAG-3000-SWI-2"1/2-77
CAG-3000-SWI-2"1/2-81		 64 80 76.1 73.02 74
77
81		 98 58 24 84.1 130
CAG-3000-SWI-3"-90.5 76 90   88.9 90.5 116 70 28 101.6 150

* SWI flanges head may only be fitted with split-flanges (the shoulder does not allow a one piece fitting to pass through).
These references design groove flanged head for 0'Ring
To design a flanged head without any groove, replace CAG by CSG
Without flanged head 0'Ring


FLANGED HEAD SOCKET WELDING (SWI)
ISO 6162-2 - S.A.E. 6000
Part N° DN Outer diameter tube Ø L1 Ø L2 Ø A K Ø C L
MM GAZ SCHD
CAG-6000-SWI-1/2"-20.5
CAG-6000-SWI-1/2"-21.7
CAG-6000-SWI-1/2"-22.5		 13 20
22		 21.25 21.34 20.5
21.7
22.5		 32
32
32		 13
13
13		 13
13
13		 32
32
32		 60
60
60
CAG-6000-SWI-3/4"-25.7
CAG-6000-SWI-3/4"-27.3
CAG-6000-SWI-3/4"-28.7		 19 25
28		 26.75 26.68 25.7
27.3
28.7		 40
40
40		 17.5
17.5
17.5		 13
13
13		 41.6
41.6
41.6		 68
68
68
CAG-6000-SWI-1"-34
CAG-6000-SWI-1"-35.5		 25 35 33.50 33.40 34
35.5		 48
48		 22
22		 16
16		 47.9
47.9		 75
75

* SWI flanges head may only be fitted with split-flanges (the shoulder does not allow a one piece fitting to pass through).
These references design groove flanged head for 0'Ring
To design a flanged head without any groove, replace CAG by CSG
Without flanged head 0'Ring
+ -

FLANGED HEAD BUTT WELDING (BWI)
SAE 3000 / SAE 6000
& PN250 / PN400
Click to collapse
Collets butt welding passage integral
FLANGED HEAD BUTT WELDING (BWI)
S.A.E. 3000 - CETOP / 250
Part N° DN Ø A Ø C Ø H Ø H1 L
CAG-250-3000-BWI-3/8
CAG-250-3000-BWI-1/2		 10
13		 12
13		 24.5
30.5		 18
24		 18
22		 40
45
CAG-250-3000-BWI-3/4 19 19 38.4 31.5 28 50
CAG-250-3000-BWI-1"
CAG-250-3000-BWI-1"1/4		 25
32		 25
32		 44.7
51.1		 38
43		 35
43		 55
60
CAG-250-3000-BWI-1"1/2 38 38 60.6 50 50 65
CAG-250-3000-BWI-2"
CAG-3000-BWI-2"1/2		 51
64		 47
58		 71.4
84.1		 61.8
74		 61.8
74		 70
75
CAG-250-BWI-2"1/2 64 58 87.2 76 76 75
CAG-250-3000-BWI-3"
CAG-3000-BWI-3"1/2		 76
89		 70
86		 101.6
114.3		 90
102		 90
102		 85
90
CAG-250-BWI-3"1/2 89 77 119 102 102 90
CAG-3000-BWI-4"
CAG-250-BWI-4"		 102
102		 96
90		 127
131		 114
114		 114
114		 100
100

Without flanged head 0'Ring
These references design groove flanged head for 0'Ring
To design a flanged head without any groove, replace CAG by CSG


FLANGED HEAD BUTT WELDING (BWI)
S.A.E. 6000 - CETOP / 400
Part N° DN Ø A Ø C Ø H Ø H1 L
CAG-400-BWI-3/8
CAG-400-6000-BWI-1/2		 10
13		 11
13		 26
32		 18
24		 17.5
22		 40
45
CAG-6000-BWI-3/4 19 17.5 41.6 32 28 50
CAG-400-BWI-3/4
CAG-400-6000-BWI-1"		 19
25		 17.5
22		 39.5
47.9		 32
38		 28
35		 50
55
CAG-400-6000-BWI-1"1/4 32 29 54.3 43.8 43.8 60
CAG-400-6000-BWI-1"1/2
CAG-400-6000-BWI-2"		 38
51		 35
43		 63.8
79.4		 50.6
67		 50.6
65		 65
70
CAG-400-BWI-2"1/2 56 53 94.2 80 76 80
CAG-400-BWI-3"
CAG-400-BWI-3"1/2		 63
70		 58
63		 104
119		 90
102		 90
102		 90
90
CAG-400-BWI-4" 80 74 131 114 114 110

Without flanged head 0'Ring
These references design groove flanged head for 0'Ring
To design a flanged head without any groove, replace CAG by CSG
+ -

REDUCING FLANGED HEAD BUTT WELDING (BWR)
SAE 3000 / SAE 6000 &
PN250 / PN400
Click to collapse
Collets butt welding a passage reduit
REDUCING FLANGED HEAD BUTT WELDING (BWR)
S.A.E. 3000 - CETOP / 250
Part N° DN Ø A Ø C Ø H Ø H1 L
CAG-250-3000-BWR-1/2"
CAG-250-3000-BWR-3/4"		 13
19		 12
13		 30.5
38.4		 24
31.5		 18
22		 45
50
CAG-250-3000-BWR-1" 25 19 44.7 38 28 55
CAG-250-3000-BWR-1"1/4
CAG-250-3000-BWR-1"1/2		 32
38		 25
32		 51.1
60.6		 43
50		 35
43		 60
65
CAG-250-3000-BWR-2" 51 38 71.4 61.8 50 70
CAG-3000-BWR-2"1/2
CAG-250-BWR-2"1/2		 64
64		 47
47		 84.1
87.2		 74
76		 61.8
61.8		 75
75
CAG-250-3000-BWR-3" 76 58 101.6 90 76 85
CAG-3000-BWR-3"1/2
CAG-250-BWR-3"1/2		 89
89		 70
70		 114.3
119		 102
102		 90
90		 90
90
CAG-3000-BWR-4" 102 80 127 114 102 100
CAG-250-BWR-4" 102 80 131 114 102 100

Reduced passage means a reduced diameter at the pipe compared with the DN of Flanged Head, see Ø A.
Without flanged head 0'Ring
These references design groove flanged head for 0'Ring
To design a flanged head without any groove, replace CAG by CSG


REDUCING FLANGED HEAD BUTT WELDING (BWR)
S.A.E. 6000 - CETOP / 400
Part N° DN Ø A Ø C Ø H Ø H1 L
CAG-400-6000-BWR-1/2"
CAG-6000-BWR-3/4"		 13
19		 11
13		 32
41.6		 24
32		 17.5
22		 45
50
CAG-400-BWR-3/4" 19 13 39.5 32 22 50
CAG-400-6000-BWR-1"
CAG-400-6000-BWR-1"1/4		 25
32		 17.5
22		 47.9
54.3		 38
43.8		 28
35		 55
60
CAG-400-6000-BWR-1"1/2 38 29 63.8 50.6 43.8 65
CAG-400-6000-BWR-2"
CAG-400-BWR-2"1/2		 51
56		 35
43		 79.4
94.2		 67
80		 51
65		 70
80
CAG-400-BWR-3" 63 53 104 90 80 90
CAG-400-BWR-3"1/2
CAG-400-BWR-4"		 70
80		 58
63		 119
131		 102
114		 90
102		 90
110

Reduced passage means a reduced diameter at the pipe compared with the DN of Flanged Head, see Ø A.
Without flanged head 0'Ring
These references design groove flanged head for 0'Ring
To design a flanged head without any groove, replace CAG by CSG
+ -

REDUCING FLANGED HEAD SOCKET WELDING (SWR)
SAE 3000 / SAE 6000 &
PN250 / PN400
Click to collapse
Collets socket welding a passage reduit SWR
REDUCING FLANGED HEAD SOCKET WELDING (SWR)
S.A.E. 3000 - CETOP / 250
Part N° DN Outer diameter tube Ø A Ø C Ø L1 Ø L2 K L
MM GAZ SCHD
CAG-250-3000-SWR-1/2"-16.3
CAG-250-3000-SWR-1/2"-17.6		 13 16 16.75 17.14 12
12		 30.5
30.5		 16.3
17.6		 24
24		 12
12		 35
35
CAG-250-3000-SWR-3/4"-18.5
CAG-250-3000-SWR-3/4"-20.5		 19 18
20		     13
13		 38.4
38.4		 18.5
20.5		 31.5
31.5		 13
13		 40
40
CAG-250-3000-SWR-3/4"-21.7   21.25 21.34 13 38.4 21.7 31.5 13 40
CAG-250-3000-SWR-1"-25.5
CAG-250-3000-SWR-1"-27.3		 25 25 26.75 26.68 19
19		 44.7
44.7		 25.5
27.3		 38.
38		 14
14		 45
45
CAG-250-3000-SWR-1"1/4-30.5
CAG-250-3000-SWR-1"1/4-32.5
CAG-250-3000-SWR-1"1/4-34		 32 30
32		 33.50 33.40 25
25
25		 51.1
51.1
51.1		 30.5
32.5
34		 43
43
43		 16
16
16		 50
50
50
CAG-250-3000-SWR-1"1/4-35.5 35     25 51.1 35.5 43 16 50
CAG-250-3000-SWR-1"1/2-38.5
CAG-250-3000-SWR-1"1/2-40.5
CAG-250-3000-SWR-1"1/2-43		 38 38
40
42		 42.25 42.16 32
32
32		 60.6
60.6
60.6		 38.5
40.5
43		 50
50
50		 18
18
18		 55
55
55
CAG-250-3000-SWR-2"-49
CAG-250-3000-SWR-2"-50.7		 51 50 48.25 48.26 38
38		 71.4
71.4		 49
50.7		 61.8
61.8		 20
20		 65
65
CAG-3000-SWR-2"1/2-61
CAG-3000-SWR-2"1/2-65.8
CAG-250-SWR-2"1/2-61
CAG-250-SWR-2"1/2-65.8		 64 60
65
60
65		 60.30
60.30		 60.32 47
47
47
47		 84.1
84.1
87.2
87.2		 61
65.8
61
65.8		 73.8
73.8
76
76		 22
22
22
22		 75
75
75
75
CAG-250-3000-SWR-3"-74
CAG-250-3000-SWR-3"-77
CAG-250-3000-SWR-3"-81		 76 80 76.10 73.02 58
58
58		 101.6
101.6
101.6		 74
77
81		 90
90
90		 24
24
24		 85
85
85

Reduced passage means a reduced diameter at the pipe compared with the flange head, materialized by Ø C.
Without flanged head 0'Ring
These references design groove flanged head for 0'Ring
To design a flanged head without any groove, replace CAG by CSG


REDUCING FLANGED HEAD SOCKET WELDING (SWR)
S.A.E. 6000 - CETOP / 400
Part N° DN Outer diameter tube Ø A Ø C Ø L1 Ø L2 K L
MM GAZ SCHD
CAG-400-6000-SWR-1/2"-16.3
CAG-400-6000-SWR-1/2"-17.6		 13 16 16.75 17.14 11
11		 32
32		 16.3
17.6		 24
24		 13
13		 35
35
CAG-6000-SWR-3/4"-18.5 19 18     13 41.6 18.5 31.8 13 40
CAG-400-SWR-3/4"-18.5 18     13 39.5 18.5 31.8 13 40
CAG-6000-SWR-3/4"-20.5 20     13 41.6 20.5 31.8 13 40
CAG-400-SWR-3/4"-20.5 20     13 39.5 20.5 31.8 13 40
CAG-6000-SWR-3/4"-21.7   21.15 21.34 13 41.6 21.7 31.8 13 40
CAG-400-SWR-3/4"-21.7   21.25 21.34 13 39.5 21.7 31.8 13 40
CAG-400-6000-SWR-1"-25.5
CAG-400-6000-SWR-1"-27.3		 25 25 26.75 26.68 17.5
17.5		 47.9
47.9		 25.5
27.3		 38
38		 13
13		 45
45
CAG-400-6000-SWR-1"1/4-30.5 32 30     22 54.3 30.5 44 16 50
CAG-400-6000-SWR-1"1/4-32.5 32     22 54.3 32.5 44 16 50
CAG-400-6000-SWR-1"1/4-34   33.50 33.40 22 54.3 34 44 16 50
CAG-400-6000-SWR-1"1/4-35.5 35     22 54.3 35.5 44 16 50
CAG-400-6000-SWR-1"1/2-38.5
CAG-400-6000-SWR-1"1/2-40.5
CAG-400-6000-SWR-1"1/2-42.8		 38 38
40
42		 42.25 42.16 29
29
29		 63.8
63.8
63.8		 38.5
40.5
42.8		 51
51
51		 18
18
18		 55
55
55
CAG-400-6000-SWR-2"49 51  50 48.25 48.26 35 79.4 49 67 20 65
CAG-400-6000-SWR-2"50.8     35 79.4 50.8 67 20 65

Reduced passage means a reduced diameter at the pipe compared with the flange head, materialized by Ø C.
Without flanged head 0'Ring
These references design groove flanged head for 0'Ring
To design a flanged head without any groove, replace CAG by CSG

Adaptors

Adapteurs
SOCKET WELDING ADAPTORS
Part N° DN Outer diameter tube Ø A Ø C Ø L1 Ø L2 K L
MM GAZ SCHD
AD-SWI/BW-1/2"-20.5
AD-SWI/BW-1/2"-21.7		 13
13		 20 21.25 21.34 20.5
21.7		 30
30		 22
22		 13
13		 13
13		 30
30
AD-SWI/BW-3/4"-25.5
AD-SWI/BW-3/4"-27.3		 19
19		 25 26.75 26.68 25.5
27.3		 35
35		 28
28		 19
19		 13
13		 30
30
AD-SWI/BW-1"-30.5
AD-SWI/BW-1"-32.5
AD-SWI/BW-1"-34
AD-SWI/BW-1"35.5		 25
25
25
25		 30
32
35		 33.50 33.40 30.5
32.5
34
35.5		 44
44
44
44		 35
35
35
35		 25
25
25
25		 16
16
16
16		 35
35
35
35
AD-SWI/BW-1"1/4-38.5
AD-SWI/BW-1"1/4-40.5		 32
32		 38
40		     38.5
40.5		 55
55		 43
43		 32
32		 18
18		 45
45
AD-SWI/BW-1"1/4-43 32 42 42.25 42.16 43 55 43 32 18 45
AD-SWI/BW-1"1/2-49
AD-SWI/BW-1"1/2-50.4		 38
38		 48
50		 48.25 48.26 49
50.4		 63
63		 50
50		 38
38		 20
20		 50
50
AD-SWI/BW-2"-61 51 60 60.30 60.32 61 79 62 47 22 55
AD-SWI/BW-2"65.8 51 65     65.8 79 62 47 22 55

Adapters allowing after welding a Butt Welding flang head to be changed to a Socket Welding flange head with pipe sweating, as shown on the drawing above.
To be welded on a Butt Welding flange head of the same DN

Flanges Plug

Obturateurs

FLANGES PLUG
S.A.E. 3000 - CETOP / 250
Part N° DN Ø C H L
OBAG-250-3000-3/8"
OBAG-250-3000-1/2"		 10
13		 24.5
30.5		 18
24		 15
15
OBAG-250-3000-3/4" 19 38.4 31.5 16
OBAG-250-3000-1"
OBAG-250-3000-1"1/4		 25
32		 44.7
51.1		 38
43		 18
18
OBAG-250-3000-1"1/2 38 60.6 50 18
OBAG-250-3000-2"
OBAG-250-2"1/2		 51
64		 71.4
87.2		 61.8
76		 21
21
OBAG-3000-2"1/2 64 84.1 73.8 21
OBAG-250-3000-3"
OBAG-250-3"1/2		 76
89		 101.6
119		 90
102		 24
45
OBAG-3000-3"1/2 89 114.2 102 45
OBAG-250-4"
OBAG-3000-4"		 102
102		 131
127		 114
114		 55
55

Obturateurs
FLANGES PLUG
S.A.E. 6000 - CETOP /400
Part N° DN Ø C H L
OBAG-400-3/8"
OBAG-400-6000-1/2"		 10
13		 26
32		 18
24		 18
19
OBAG-400-3/4" 19 39.5 32 21
OBAG-6000-3/4"
OBAG-400-6000-1"		 19
25		 41.6
47.9		 32
38		 21
26
OBAG-400-6000-1"1/4 32 54.3 43.8 31
OBAG-400-6000-1"1/2
OBAG-400-6000-2"		 38
51		 63.8
79.4		 50.8
66.5		 34
42
OBAG-400-2"1/2 56 94.2 80 47
OBAG-400-3"
OBAG-400-3"1/2		 63
70		 104
119		 90
102		 54
61
OBAG-400-4" 80 131 114 61

Threaded Flanged Head

+ -

THREADED FLANGED HEAD BSPP
SAE 3000 / SAE 6000 & PN250 / PN400
Click to collapse
Collets filetes bsp cylindrique
THREADED FLANGED HEAD BSPP
S.A.E. 3000 - CETOP / 250
Part N° PN bar1 DN Ø F.BSP cyl. Ø A Ø C L S
CAG-3000-F-G-CYL-1/2"-A *
CAG-250-3000-F-G-CYL-1/2"-B		 300 13
13		 1/2"
3/8"		 11
9		 30.5
30.5		 50
50		 21
19
CAG-250-3000-F-G-CYL-3/4"-A
CAG-250-3000-F-G-CYL-3/4"-B		 19
19		 3/4"
1/2		 17
11		 38.4
38.4		 60
60		 26
26
CAG-250-3000-F-G-CYL-1"-A**
CAG-250-3000-F-G-CYL-1"-B		 25
25		 1"
3/4		 22
17		 44.7
44.7		 65
65		 32
32
CAG-3000-F-G-CYL-1"1/4-A *
CAG-250-3000-F-G-CYL-1"1/4-B		 150 32
32		 1"1/4
1"		 30
22		 51.1
51.1		 70
70		 41
41
CAG-3000-F-G-CYL-1"1/2-A *
CAG-250-3000-F-G-CYL-1"1/2-B		 38
38		 1"1/2
1"1/4		 36
30		 60.6
60.6		 75
75		 50
41
CAG-3000-F-G-CYL-2"-A *
CAG-250-3000-F-G-CYL-2"-B		 51
51		 2"
1"1/2		 44
36		 71.4
71.4		 80
80		 55
50

(1)Pressure max. recommended.
Male threaded BSPP (ISO 228/NF E 03-005), sealing with ring "BS" or cupper 0'Ring.
Without flanged head 0'Ring.
These references design groove flanged head for 0'Ring.
To design a flanged head without any groove, replace CAG by CSG.
** assembles itself with joint only coppers, for ring BS consult us
NOTE : Further to the sealing, some of flanged head can be use only with split flanges, they are indicated into the references by only 3000 or 6000


THREADED FLANGED HEAD BSPP
S.A.E. 6000 - CETOP / 400
Part N° PN bar1 DN Ø F.BSP cyl. Ø A Ø C L S
CAG-6000-F-G-CYL-1/2"-A *
CAG-400-6000-F-G-CYL-1/2"-B		 350 13
13		 1/2"
3/8"		 10
8		 32
32		 60
60		 21
19
CAG-6000-F-G-CYL-3/4"-A *
CAG-6000-F-G-CYL-3/4"-B *
CAG-400-F-G-CYL-3/4"-A
CAG-400-F-G-CYL-3/4"-B		 19
19
19
19		 3/4"
1/2"
3/4"
1/2"		 16
10
16
10		 41.6
41.6
39.5
39.5		 60
60
60
60		 26
26
26
26
CAG-6000-F-G-CYL-1"-A *
CAG-400-6000-F-G-CYL-1"-B		 25
25		 1"
3/4		 20
16		 47.9
47.9		 70
70		 32
32
CAG-6000-F-G-CYL-1"1/4-A *
CAG-400-6000-F-G-CYL-1"1/4-B		 250 32
32		 1"1/4
1"		 26
20		 54.3
54.3		 75
75		 41
32
CAG-6000-F-G-CYL-1"1/2-A *
CAG-400-6000-F-G-CYL-1"1/2-B		 38
38		 1"1/2
1"1/4		 30
26		 63.8
63.8		 80
80		 50
41
CAG-6000-F-G-CYL-2"-A *
CAG-400-6000-F-G-CYL-2"-B		 200 51
51		 2"
1"1/2		 40
30		 79.4
79.4		 90
90		 55
55

(1)Pressure max. recommended.
Male threaded BSPP (ISO 228/NF E 03-005), sealing with ring "BS" or cupper 0'Ring.
Without flanged head 0'Ring.
These references design groove flanged head for 0'Ring.
To design a flanged head without any groove, replace CAG by CSG.
** assembles itself with joint only coppers, for ring BS consult us
NOTE : Further to the sealing, some of flanged head can be use only with split flanges, they are indicated into the references by only 3000 or 6000
+ -

THREADED FLANGED HEAD BSP STUD AND NPT
SAE 3000 / SAE 6000 &
PN250 / PN400
Click to collapse
Collets filetes gaz conique et npt
THREADED FLANGED HEAD BSP STUD AND NPT
S.A.E. 3000 - CETOP / 250
Part N° PN bar1 DN Ø F Gaz co. Ø A Ø C L S
CAG-250-3000-F-G-CO-1/2"-A
CAG-250-3000-F-G-CO-1/2"-B		 300 13 1/2"
3/8"		 12
10		 30.5 50 19
CAG-250-3000-F-G-CO-3/4"-A 19 3/4" 17 38.4 55 27
CAG-250-3000-F-G-CO-3/4"-B 1/2" 12
CAG-250-3000-F-G-CO-1"-A
CAG-250-3000-F-G-CO-1"-B		 25 1"
3/4"		 22
17		 44.7 60 32
CAG-250-3000-F-G-CO-1"1/4-A 150 32 1"1/4 27 51.1 65 41
CAG-250-3000-F-G-CO-1"1/4-B 1" 22
CAG-250-3000-F-G-CO-1"1/2-A
CAG-250-3000-F-G-CO-1"1/2-B		 38 1"1/2
1"1/4		 32
27		 60.6 70 46
CAG-250-3000-F-G-CO-2"-A 51 2" 40 71.4 75 55
CAG-250-3000-F-G-CO-2"-B 1"1/2 30

(1) Pressure max. recommended.
Without flanged head 0'Ring.
These references design groove flanged head for 0'Ring.
To design a flanged head without any groove, replace CAG by CSG.
For threaded NPT, replace G CO by NPT into the reference.
Male JIC Threaded flanged on request.


THREADED FLANGED HEAD BSP STUD AND NPT
S.A.E. 6000 - CETOP / 400
Part N° PN bar1 DN Ø F Gaz co. Ø A Ø C L S
CAG-400-6000-F-G-CO-1/2"-A
CAG-400-6000-F-G-CO-1/2"-B		 350 13 1/2"
3/8"		 12
10		 32 50 19
CAG-6000-F-G-CO-3/4"-A 19 3/4" 17 41.6 60 26
CAG-6000-F-G-CO-3/4"-B 1/2" 12
CAG-400-F-G-CO-3/4"-A 3/4" 17 39.5 60 26
CAG-400-F-G-CO-3/4"-B 1/2" 12
CAG-400-6000-F-G-CO-1"-A
CAG-400-6000-F-G-CO-1"-B		 25 1"
3/4		 22
17		 47.9 70 32
CAG-400-6000-F-G-CO-1"1/4-A 250 32 1"1/4 27 54.3 75 36
CAG-400-6000-F-G-CO-1"1/4-B 1" 22
CAG-400-6000-F-G-CO-1"1/2-A
CAG-400-6000-F-G-CO-1"1/2-B		 38 1"1/2
1"1/4		 30
27		 63.8 80 41
CAG-400-6000-F-G-CO-2"-A 200 51 2" 40 79.4 90 55
CAG-400-6000-F-G-CO-2"-B 1"1/2 30

(1) Pressure max. recommended.
Without flanged head 0'Ring.
These references design groove flanged head for 0'Ring.
To design a flanged head without any groove, replace CAG by CSG.
For threaded NPT, replace G CO by NPT into the reference.
Male JIC Threaded flanged on request.
+ -

THREADED FLANGED HEAD DIN 2353 (24°) ISO 8434-1 AND 4
SAE 3000 / SAE 6000 &
PN250 / PN400
Click to collapse
Collets filetes metriques a cone interieur 24
THREADED FLANGED HEAD DIN 2353 (24°) ISO 8434-1 AND 4
S.A.E. 3000 - CETOP / 250
Part N° PN bar1 DN Ø F Ø D x série Ø A Ø C L S
CAG-250-3000-F-DIN-1/2"-A
CAG-250-3000-F-DIN-1/2"-B
CAG-250-3000-F-DIN-1/2"-C
CAG-3000-F-DIN-1/2"-D		 315 13
13
13
13		 M 20X1.5
M 22X1.5
M 24X1.5
M 26X1.5		 12 S
15 L
16 S
18 L		 8
12
12
14		 30.5
30.5
30.5
30.5		 50
50
50
50		 19
19
19
19
350
315
CAG-250-3000-F-DIN-3/4"-A 350 19 M 24X1.5 16 S 12 38.4 55 27
CAG-250-3000-F-DIN-3/4"-B 19 M 30X2 20 S 16 38.4 55 27
CAG-250-3000-F-DIN-3/4"-C 160 19 M 30X2 22 L 18 38.4 55 27
CAG-250-3000-F-DIN-1"-A
CAG-250-3000-F-DIN-1"-B
CAG-250-3000-F-DIN-1"-C		 315 25
25
25		 M 30X2
M 36X2
M 36X2		 20 S
25 S
28 L		 16
20
23		 44.7
44.7
44.7		 60
60
60		 32
32
32
160
CAG-250-3000-F-DIN-1"1/4-A 250 32 M 36X2 25 S 20 51.1 60 41
CAG-250-3000-F-DIN-1"1/4-B 32 M 42X2 30 S 25 51.1 60 41
CAG-3000-F-DIN-1"1/4-C 160 32 M 45X2 35 L 30 51.1 60 41
CAG-250-3000-F-DIN-1"1/2-A
CAG-3000-F-DIN-1"1/2-B
CAG-3000-F-DIN-1"1/2-C		 38
38
38		 M 45X2
M 52X2
M 52X2		 35 L
42 L
38 S		 30
36
32		 60.6
60.6
60.6		 65
65
65		 46
46
46
200

Pressure max. recommended.
Without flanged head 0'Ring.
These references design groove flanged head for 0'Ring.
To design a flanged head without any groove, replace CAG by CSG.


THREADED FLANGED HEAD DIN 2353 (24°) ISO 8434-1 AND 4
S.A.E. 6000 - CETOP / 400
Part N° PN bar1 DN Ø F Ø D x série Ø A Ø C L S
CAG-400-6000-F-DIN-1/2"-A
CAG-400-6000-F-DIN-1/2"-B
CAG-400-6000-F-DIN-1/2"-C		 400 13 M 20X1.5
M 22X1.5
M 24X1.5		 12 S
14 S
16 S		 8
10
12		 32 50 19
CAG-6000-F-DIN-3/4"-A 19 M 24X1.5 16 S 12 41.6 65 30
CAG-6000-F-DIN-3/4"-B M 30X2 20 S 16
CAG-6000-F-DIN-3/4"-C 160 M 30X2 22 L 18
CAG-400-6000-F-DIN-1"-A
CAG-400-6000-F-DIN-1"-B
CAG-400-6000-F-DIN-1"-C		 400 25 M 30X2
M 36X2
M 36X2		 20 S
25 S
28 L		 16
20
23		 47.9 75 36
160
CAG-400-6000-F-DIN-1"1/4-A 400 32 M 36X2 25 S 20 54.3 80 41
CAG-400-6000-F-DIN-1"1/4-B M 42X2 30 S 25
CAG-6000-F-DIN-1"1/4-C 160 M 45X2 35 L 30
CAG-6000-F-DIN-1"1/2-A
CAG-6000-F-DIN-1"1/2-B
CAG-6000-F-DIN-1"1/2-C		 400 38 M 42X2
M 52X2
M 52X2		 30 S
38 S
42 L		 25
32
36		 63.8 90 46
160

Pressure max. recommended.
Without flanged head 0'Ring.
These references design groove flanged head for 0'Ring.
To design a flanged head without any groove, replace CAG by CSG.

Socket welding connectors

+ - SOCKET WELDING CONNECTORS 3000 PSI
Manchons a souder droit 01 Click to collapse
SOCKET WELDING CONNECTORS 3000 PSI
Part N° DN Ø A* L* Ø d K* Ø D*
MA-EG-3000-1/4" 1/4" 9 25.5 13.8 9.5 22
MA-EG-3000-3/8" 3/8" 12.5 25.5 17.5 9.5 26
MA-EG-3000-1/2" 1/2" 15 28.5 21.7 9.5 32
MA-EG-3000-3/4" 3/4" 20 35 27 13 38
MA-EG-3000-1" 1" 25 38 33.7 13 45
MA-EG-3000-1"1/4 1"1/4 32 38 42.5 16 55
MA-EG-3000-1"1/2 1"1/2 40 38 48.6 16 65
MA-EG-3000-2" 2" 50 50.5 61 20 75

Stainless Steel on request
NOTA : Dimensions for information may be changed depending on production
+ - MANCHONS A SOUDER SOCKET WELDING (SW) SERIE 3000 PSI
Manchons a souder droit 02 Click to collapse
MANCHONS A SOUDER SOCKET WELDING (SW) SERIE 3000 PSI
Part N° DN Ø A* L* Ø d Ø dl K* K1* Ø D*
MA-RE-3000-1/4"-1/8" 1/4"-1/8" 6 25.5 13.8 10.5 9.5 9,5 22
MA-RE-3000-3/8"-1/4" 3/8"-1/4" 9 25.5 17.5 13.8 9.5 9.5 26
MA-RE-3000-1/2"-3/8" 1/2"-3/8" 12.5 28.5 21.7 17.5 9.5 9.5 32
MA-RE-3000-3/4"-1/2" 3/4"-1/2" 15 35 27 21.7 9.5 13 38
MA-RE-3000-1"-3/4" 1"-3/4 20 38 33.7 27 13 13 45
MA-RE-3000-1"1/4-1" 1"1/4-1" 25 38 42.5 33.7 13 16 55
MA-RE-3000-1"1/2-1"1/4 1"1/2-1"1/4 32 38 48.6 42.5 16 16 65
MA-RE-3000-2"-1"1/2 2"-1"1/2 40 50.5 61 48.6 16 20 75

Stainless Steel on request
NOTA : Dimensions for information may be changed depending on production
+ - SOCKET WELDING (SW) SERIE 3000 PSI - 90° ELBOW
Manchons a souder coude Click to collapse
SOCKET WELDING (SW) SERIE 3000 PSI - 90° ELBOW
Part N° DN Ø A* L* Ø d K* Ø D*
MA-90-3000-1/4" 1/4" 9 24 13.8 9.5 25
MA-90-3000-3/8" 3/8" 12.5 24 17.5 9.5 25
MA-90-3000-1/2" 1/2" 15 28 21.7 9.5 33
MA-90-3000-3/4" 3/4" 20 34 27 13 38
MA-90-3000-1" 1" 25 38 33.7 13 46
MA-90-3000-1"1/4 1"1/4 32 44 42.5 16 56
MA-90-3000-1"1/2 1"1/2 40 50 48.6 16 62
MA-90-3000-2" 2" 50 60 61 20 76

Stainless Steel on request
NOTA : Dimensions for information may be changed depending on production
+ - SOCKET WELDING (SW) SERIE 3000 PSI - TEE
Manchons a souder te Click to collapse
SOCKET WELDING (SW) SERIE 3000 PSI - TEE
Part N° DN Ø A* L1* Ø d K* Ø D* L*
MA-TE-3000-1/4" 1/4" 9 24 13.8 9.5 25 48
MA-TE-3000-3/8" 3/8" 12.5 24 17.5 9.5 25 48
MA-TE-3000-1/2" 1/2" 15 28 21.7 9.5 33 56
MA-TE-3000-3/4" 3/4" 20 34 27 13 38 68
MA-TE-3000-1" 1" 25 38 33.7 13 46 76
MA-TE-3000-1"1/4 1"1/4 32 44 42.5 16 56 88
MA-TE-3000-1"1/2 1"1/2 40 50 48.6 16 62 100
MA-TE-3000-2" 2" 50 60 61 20 76 120

Stainless Steel on request
NOTA : Dimensions for information may be changed depending on production

Seales

Joints toriques
0'RINGS
DN Part N° Ø int. x Ø tore Assembly
3/8" JT 1712-262 17.12 X 2.62 3000 - PN 250/400
1/2" JT 1864-353 18.64 X 3.53 3000/6000 - PN 250/400
3/4" JT 2499-353 24.99 X 3.53 3000/6000 - PN 250/400
1" JT 3292-353 32.92 X 3.53 3000/6000 - PN 250/400
1"1/4 JT 3769-353 37.69 X 3.53 3000/6000 - PN 250/400
1"1/2 JT 47.22-353 47.22 X 3.53 3000/6000 - PN 250/400
2" JT 56.74-353 56.74 X 3.53 3000/6000 - PN 250/400
2"1/2 JT 6944-353 69.44 X 3.53 3000 PSI - PN 250
2"1/2 JT 6922-533 69.22 X 5.33 PN 400
3" JT 8532-353 85.32 X 3.53 3000 PSI - PN 250
3" JT 7557-533 75.57 X 5.33 PN 400
3"1/2 JT 9802-353 98.02 X 3.53 3000 PSI
3"1/2 JT 8532-353 85.32 X 3.53 PN 250
3"1/2 JT 8509-533 85.09 X 5.33 PN 400
4" JT 11072-353 110.72 X 3.53 3000 PSI
4" JT 9802-353 98.02 X 3.53 PN 250
4" JT 8827-533 88.27 X 5.33 PN 400

Our seales are delivered as shore 90 quality standard whether in Perbunan or Viton.
If you want Viton seal, add "V" after the reference.
Contact us for liquids other than hydraulic oils, particularly liquids called "nonflammable" and for use at high temperature.


JOINT SQUARE FOR FLANGES SAE J518C
Part N° Nominal diameter Flange Part N° Diam. D
JT CARRE 25.5x2.92
PU (DN 13)		 1/2" 08 25,50
JT CARRE 31.8x2.92
PU (DN 19)		 3/4" 12 31,80
JT CARRE 39.7x2.92
PU (DN 25)		 1" 16 39,70
JT CARRE 44.4x2.92
PU (DN 32)		 1"1/4 20 44,40
JT CARRE 53.9x2.92
PU (DN 38)		 1"1/2 24 53,90
JT CARRE 63.5x2.92
PU (DN 51)		 2" 32 63,50
JT CARRE 78.3x2.92
PU (DN 64)		 2"1/2 40 78,30
JT CARRE 92.1x2.92
PU (DN 76)		 3" 48 92,10
JT CARRE 104.5x2.92
PU (DN 89)		 3"1/2 56 104,50
JT CARRE 117.2x2.92
PU (DN 102)		 4" 64 117,20
JT CARRE 142.6x2.92
PU (DN 127)		 5" 80 142,60

Joints square are especially designed for the applications of facial sealing (for tubes to supports, connections for test hoses) according to the reference frame standardized SAE J518c.
Joints square ensure a replacement instead of O rings commonly used for these applications.
The square joint is produced of only one part, composed of an external PU element 95 Shore A
© 2023 Tecalemit Flexibles. All Rights Reserved.
To Top
Saturday, March 25, 2023
Save
Cookies user preferences
We use cookies to ensure you to get the best experience on our website. If you decline the use of cookies, this website may not function as expected.
Accept all
Decline all
Analytics
Tools used to analyze the data to measure the effectiveness of a website and to understand how it works.
Google Analytics
Accept
Decline
Unknown
Unknown
Accept
Decline