 |
|
Coupling for compressed air : Express couplings & Air King couplings
Symmetrical rapid-lock quarter-turn couplings, comprising different rear parts depending on where they are intended to be installed. Fluted Express coupling, female threaded Express, male threaded, swivel connection, Hose connection with safety collar, rubber gasket, clamping jaw, safety pin and female jonction - European-type. - American-type.
|
Warning concerning couplings intended for gaseous fluids
We would like to insist on the need to make a perfectly suitable choice of couplings and locking collars/rings on the compressed air pipe concerned. In fact, as the fluid is compressed by definition, the damage if the hose breaks is much greater than that caused by a fault on a hose transporting an incompressible fluid. You can compare the breakage of a hose under pressure to compressed gas during an explosion.
Express couplings sizes :
 |
Key : 1 : Triggering notch 2 : Catch NOTE 1: The max. 25 mm diameter delimits a minimum bearing crown of the flange joint. NOTE 2: The shapes and dimensions not marked are left to the interpretation of the manufacturer.
|
Table 1 – Dimensions of (grooved) sockets for polyamide tubes |
Inside hose diameter (mm) |
6 |
7,5 |
8 |
10 |
12 |
Dimension A (mm) |
4 |
6 |
6 |
8 |
10 |
NOTE: The dimensions of polyamide tubes are specified in NF E 49-100
|
Table 1 – Dimensions of (grooved) sockets for hoses based on rubber or thermoplastic materials. |
DN (mm) |
6,3 |
8 |
10 |
12,5 |
16 |
19 |
20 |
25 |
Dimension A (mm) |
4 |
6 |
8 |
10 |
12 |
15 |
15 |
21 |
The class B external cylindrical threads comply with NF EN ISO 228-1:2003.
|
 |
The class B external cylindrical threads comply with NF EN ISO 228-1:2003
|
Thraed (mm) |
/2 (mm) |
D(mm) |
Recommended width across flats(mm) |
G 1/4 B |
9 |
8 |
17 |
G 3/8 B |
9 |
9,5 |
22 |
G 1/2 B |
11 |
12,5 |
27 |
G 3/4 B |
12 |
18 |
32 |
G 1 B |
14 |
23,5 |
36 |
G 1 1/4 B |
16 |
32 |
46 |
 |
The class B internal cylindrical threads comply with NF EN ISO 228-1:2003.
1: Optional groove
|
Thread (mm) |
/3 (mm) |
M max (mm) |
Recommended width across flats (mm) |
G 1/4 |
9 |
8 |
17 |
G 3/8 |
10,1 |
12 |
22 |
G 1/2 |
13,2 |
15 |
27 |
G 3/4 |
14,5 |
21 |
32 |
G 1 |
16,8 |
25 |
36 |
G 1 1/4 |
19,1 |
25 |
46 |
Express couplings : European-type
This coupling has a machined socket with non-aggressive locking for pipe tubes, a fastening neck for fitting a handle collar as well as a catch on this neck to prevent the collar from being turned. There is no need to use a wrench to connect the pipework. The distance between the handles is 41mm, sealing is done by a seal, which may have a large hole (water application) or a small hole (air application).
Heavy series - French norm Conditions of use : Water, Compressed air Express design based on NF E29-573 standard (claw distance 41 mm). Works with all fittings based on the same standard. Safety collar with stop to be assembled with hose clamps with safety claws. Pressure : PN 10 Bar Temperature : 0°C/+70°C Matérial : forged brass, NBR lip seal type A (bore Ø15)
Part N° |
Ø |
Packaging |
1509.403 |
9 |
25 |
1509.405 |
11 |
25 |
1509.406 |
13 |
25 |
1509.408 |
16 |
20 |
1509.410 |
19 |
15 |
1509.412 |
22 |
15 |
1509.414 |
25 |
15 |
1509.510 |
30-32 |
10 |
Heavy series - French norm
Conditions of use : Water, Compressed air Express design based on NF E29-573 standard (claw distance 41mm). Works with all fittings based on the same standard. Safety collar with stop to be assembled with hose clamps with safety claws. Pressure : PN 10 Bar temperature : 0°C/+70°C Material : forged brass
Part N° |
Ø |
Packaging |
2007100000900 |
9 |
25 |
2007100001100 |
11 |
25 |
2007100001300 |
13 |
25 |
2007100001600 |
16 |
20 |
2007100001900 |
19 |
15 |
2007100002200 |
22 |
15 |
2007100002500 |
25 |
15 |
2007100003000 |
30-32 |
10 |
Conditions of use : Water, Compressed air Express design based on NF E29-573 standard (claw distance 41mm). Works with all fittings based on the same standard. Female thread ISO 228-1 Pressure : PN10 Bar Temperature : 0°C/+70°C Material : forged brass, NBR lip seal type A (bore Ø15)
Part N° |
Ø |
Packaging |
1527.492 |
1/4" |
20 |
1527.491 |
3/8" |
25 |
1527.472 |
1/2" |
25 |
1527.473 |
3/4" |
20 |
1527.494 |
1" |
20 |
1527.475 |
1"1/4 |
15 |
Conditions of use : Water, Compressed air Express design based on NF E29-573 standard (claw distance 41mm). Works with all fittings based on the same standard. Female thread ISO 228-1 Pressure : PN10 Bar Temperature : 0°C/+70°C Material : forged brass
Part N° |
Ø |
Packaging |
2007110000800 |
1/4" |
20 |
2007110001200 |
3/8" |
25 |
2007110001500 |
1/2" |
25 |
2007110002000 |
3/4" |
20 |
2007110002600 |
1" |
20 |
2007110003300 |
1"1/4 |
15 |
Conditions of use : Water, Compressed air Express design based on NF E29-573 standard (claw distance 41mm). Works with all fittings based on the same standard. Male threaded ISO 228-1 Pressure : PN 10 Bar temperature : 0°C/+70°C Material : forged brass, NBR lip seal type A (bore Ø15)
Part N° |
Ø |
Packaging |
1526.492 |
1/4" |
25 |
1526.471 |
3/8" |
30 |
1526.472 |
1/2" |
25 |
1526.473 |
3/4" |
20 |
1526.474 |
1" |
20 |
1526.475 |
1"1/4 |
20 |
Conditions of use : Water, Compressed air Express design based on NF E29-573 standard (claw distance 41mm). Works with all fittings based on the same standard. Male threaded ISO 228-1 Pressure : PN 10 Bar temperature : 0°C/+70°C Material : forged brass
Part N° |
Ø |
Packaging |
2007120000800 |
1/4" |
25 |
2007120001200 |
3/8" |
30 |
2007120001500 |
1/2" |
25 |
2007120002000 |
3/4" |
20 |
2007120002600 |
1" |
20 |
2007120003300 |
1"1/4 |
20 |
Conditions of use : Water, Compressed air Design based on NF E29-573 standard (claw distance 41 mm). Works with all fittings based on the same standard. Safety collar with stop to be assembled with hose clamps with safety claws. Pressure : PN 10 Bar Temperature : 0°C/+70°C Matérial : forged brass, NBR lip seal type A (bore Ø15)
Part N° |
Ø |
Packaging |
2005260001900 |
19 |
10 |
Conditions of use : Water, Compressed air Design based on NF E29-573 standard (claw distance 41 mm). Works with all fittings based on the same standard. Safety collar with stop to be assembled with hose clamps with safety claws. Pressure : PN 10 Bar Temperature : 0°C/+70°C Matérial : forged brass, NBR lip seal type A (bore Ø15)
Référence |
Ø |
Conditionnement |
2005270001900 |
19 |
10 |
Cast iron serie Use: Compressed air Design: according to DIN 3489(42 mm inter-claw) Pressure: PN 10 bar Temperature : -40°C/+95°C Material: Body in malleable zinc-plated cast iron, oil-resistant Perbunan joint ("GOER" model) - Formerly DIN 3483 - Collar for mounting with 3258 or 3260 clamp No collar on diameter 32 (use a collar without claw)
Part N° |
Ø |
PN |
Packaging |
3035100001300 |
13 |
10 |
10 |
3035100001600 |
15 |
10 |
10 |
3035100001900 |
19 |
10 |
10 |
3035100002500 |
25 |
10 |
10 |
3035100003200 |
32 |
10 |
10 |
Cast iron serie Use: Compressed air Design: according to DIN 3489(42 mm inter-claw) Pressure: PN 10 bar Temperature : -40°C/+95°C Material: Body in malleable zinc-plated cast iron, oil-resistant Perbunan joint ("GOER" model) Formerly model DIN 3482 ISO 228-1 gas thread
Part N° |
Ø |
Packaging |
3035110001400 |
1/4" |
10 |
3035110003800 |
3/8" |
10 |
3035110001200 |
1/2" |
10 |
3035110003400 |
3/4" |
10 |
3035110001000 |
1" |
10 |
3035110005400 |
1"1/4 |
10 |
Cast iron serie Use: Compressed air Design: according to DIN 3489(42 mm inter-claw) Pressure: PN 10 bar Temperature : -40°C/+95°C Material: Body in malleable zinc-plated cast iron, oil-resistant Perbunan joint ("GOER" model) - Perbunan seal with brass cover - M5 steel retaining screw - ISO 228-1 gas thread - Must always be assembled with a perbunan joint fitting - Direct mounting on compressor or accessories
Part N° |
Ø |
Packaging |
3035890001200 |
1/2" |
10 |
3035890003400 |
3/4" |
10 |
3035890001000 |
1" |
10 |
Cast iron serie Use: Compressed air Design: according to DIN 3489(42 mm inter-claw) Pressure: PN 10 bar Temperature : -40°C/+95°C Material: Body in malleable zinc-plated cast iron, oil-resistant Perbunan joint ("GOER" model). - Perbunan seal with brass cover - M5 steel retaining screw zingué, empreinte Torx T25 - ISO 228-1 gas thread - Must always be assembled with a perbunan joint fitting. - Direct mounting on compressor or accessories.
Part N° |
Ø |
Packaging |
3035880003800 |
3/8" |
10 |
3035880001200 |
1/2" |
10 |
3035880003400 |
3/4" |
10 |
3035880001000 |
1" |
10 |
Cast iron serie Use: Compressed air Design: according to DIN 3489(42 mm inter-claw) Pressure: PN 10 bar Temperature : -40°C/+95°C Material: Body in malleable zinc-plated cast iron, oil-resistant Perbunan joint ("GOER" model) - Formerly model DIN 3481 - ISO 228-1 gas thread - Supplied with gasket mounted 3515
Part N° |
Ø |
Packaging |
3035120001400 |
1/4" |
10 |
3035120003800 |
3/8" |
10 |
3035120001200 |
1/2" |
10 |
3035120003400 |
3/4" |
10 |
3035120001000 |
1" |
10 |
3035120005400 |
1"1/4 |
10 |
{
Steel series "ATLAS COPCO" Use: Compressed air Conception : 42 mm inter-claw, full passage Pressure: PN 10 bar Temperature : -40°C / +95°C Material: Forged galvanized steel, oil resistant Perbunan joint ("GOER" model) Assembly with clamp without claw Delivered with assembled gasket part N° 3515
Part N° |
Ø |
Packaging |
3035600001000 |
10 |
10 |
3035600001300 |
12,5 |
10 |
3035600001600 |
16 |
10 |
3035600001900 |
20 |
10 |
3035600002500 |
25 |
10 |
Steel series "ATLAS COPCO" Use: Compressed air Conception : 42 mm inter-claw, full passage Pressure: PN 10 bar Temperature : -40°C / +95°C Material: Forged galvanized steel, oil resistant Perbunan joint ("GOER" model) ISO 228-1 gas thread
Part N° |
Ø |
Packaging |
3035610003800 |
3/8" |
10 |
3035610001200 |
1/2" |
10 |
3035610003400 |
3/4" |
10 |
3035610001000 |
1" |
10 |
Steel series "ATLAS COPCO" Use: Compressed air Conception : 42 mm inter-claw, full passage Pressure: PN 10 bar Temperature : -40°C / +95°C Material: Forged galvanized steel, oil resistant Perbunan joint ("GOER" model) ISO 228-1 gas thread
Part N° |
Ø |
Packaging |
3035620003800 |
3/8" |
10 |
3035620001200 |
1/2" |
10 |
3035620003400 |
3/4" |
10 |
3035620001000 |
1" |
10 |
Steel series "ATLAS COPCO" Use: Compressed air Conception : 42 mm inter-claw, full passage Pressure: PN 10 bar Temperature : -40°C / +95°C Material: Forged galvanized steel, oil resistant Perbunan joint ("GOER" model) - "MODY" type design with rotating pin and safety nut - Assembly with clamp without claw
Part N° |
Ø Inside hose |
Ø Nominal |
Packaging |
3035640001300 |
12,5 |
10 |
5 |
3035640001900 |
20 |
17 |
5 |
3035640002500 |
25 |
19 |
5 |
"Mody" series - Safety fitting "SSG" claw coupling with machined barbed shank
Use: Compressed air (for your applications requiring absolute security) Design: according to DIN 3238: 42 mm inter-claw, full passage, rotating axis to avoid twisting of the hose, easy coupling, accidental anti-opening system (by tightening the nut after assembly), double safety stop Pressure: PN 16 bar Temperature : -40°C / +95°C Material: Claws in malleable zinc-plated cast iron, ferrule in zinc-plated steel, oil-resistant Perbunan joint ("SGOR" model) Delivered with attached gasket 3517-1 Assembly with clamp without claw
Part N° |
Ø |
Packaging |
3035700001000 |
10 |
5 |
3035700001300 |
13 |
5 |
3035700001500 |
15 |
5 |
3035700001900 |
19 |
5 |
3035700002500 |
25 |
5 |
"Mody" series - Safety fitting Claw connector "SSGI" with threaded end
Use: Compressed air (for your applications requiring absolute security) Design: according to DIN 3238: 42 mm inter-claw, full passage, rotating axis to avoid twisting of the hose, easy coupling, accidental anti-opening system (by tightening the nut after assembly), double safety stop Pressure: PN 16 bar Temperature : -40°C / +95°C Material: Claws in malleable zinc-plated cast iron, ferrule in zinc-plated steel, oil-resistant Perbunan joint ("SGOR" model) Delivered with attached gasket 3517-1 ISO 228-1 gas thread
Part N° |
Ø |
Packaging |
3035710001200 |
3/8" |
5 |
3035710001500 |
1/2" |
5 |
3035710002000 |
3/4" |
5 |
3035710002600 |
1" |
5 |
"Mody" series - Safety fitting "SSGA" claw connector with threaded end
Use: Compressed air (for your applications requiring absolute security) Conception :selon la norme DIN 3238 : 42 mm inter-claw, full passage, rotating axis to avoid twisting of the hose, easy coupling, accidental anti-opening system (by tightening the nut after assembly), double safety stop Pression :PN 16 bar Temperature :-40°C / +95°C Material: Claws in malleable zinc-plated cast iron, ferrule in zinc-plated steel, oil-resistant Perbunan joint ("SGOR" model) Delivered with attached gasket 3517-1 ISO 228-1 gas thread
Part N° |
Ø |
Packaging |
3035720001200 |
3/8" |
5 |
3035720001500 |
1/2" |
5 |
3035720002000 |
3/4" |
5 |
3035720002600 |
1" |
5 |
Blasting serie "SS T" claw fittings for hose Delivered with attached gasket 3522 Nylon body on request Use: Connection for sandblasting work Design: 58 mm between-claws, locking possible with safety pin Pressure: PN 12 bar Material: Body in malleable zinc-plated cast iron, joint in Perbunan ("SKD" model)
Part N° |
Type |
Size hose |
Lenght |
PN |
Packaging |
3032850001900 |
SS 19 T |
19 x 6 |
155 |
12 |
1 |
3032850002500 |
SS 25 T |
25 x 7 |
86 |
12 |
1 |
3032850003200 |
SS 32 T |
32 x 8 |
92 |
12 |
1 |
3032850003800 |
SS 38 T |
38 x 9 |
137 |
12 |
1 |
3032850004000 |
SS 40 T |
40 x 10 |
138 |
12 |
1 |
Blasting serie "SK T" claw fittings with threaded end,Delivered with attached gasket 3522 - ISO 228-1 gas thread et Coarse Thread Series Nylon body on request
Use: Connection for sandblasting work Design: 58 mm between-claws, locking possible with safety pin Pressure: PN 12 bar Material: Body in malleable zinc-plated cast iron, joint in Perbunan ("SKD" model)
Part N° |
Type |
Thread |
Lenght (mm) |
PN |
Packaging |
3032860003800 |
SK 38 T |
G1"1/4 |
55 |
12 |
1 |
3032860381500 |
SK 38/15 T |
G1"1/2 |
55 |
12 |
1 |
3032860005000 |
SK 50 T |
Coarse Thread 50 mm |
55 |
12 |
1 |
3032860006000 |
SK 60 T |
G2`` |
78 |
12 |
1 |
Material : red EPDM Reduced bore (type A) Ø15 Standard : NF E29-573 Condition of use : Water, air Temperature : -10°C / +90°C
Part N° |
Reduced bore |
PN |
Packaging |
2005190000000 |
15 |
10 |
10 |
Material : red EPDM Full bore (type A) : 21 mm Standard : NF E29-573 Condition of use : Water, air Temperature : -10°C / +90°C
Part N° |
Full bore |
PN |
Packaging |
2005290000000 |
21 |
10 |
10 |
Conditions of use : Oil, air Temperature : -40°C/+95°C
Part N° |
Model |
Full bore |
Height |
Shore |
Packaging |
3035170000001 |
SGOR-n |
30 |
4 |
75 |
50 |
Size : Ø 34 x Height 10,5 mm Full bore: 20 mm Temperature : -40°C / +200°C Shore : 65 Conditions of use : Steam
Part N° |
Shore |
Packaging |
3035160000000 |
65 |
10 |
Standard : NF E29-573 Conditions of use : Water, air Temperature : -10°C +90°C
Part N° |
Full bore |
PN |
Packaging |
2005240000000 |
21 |
10 |
10 |
Size : Ø 34 x height 10,5 mm Full bore: 20 mm Temperature : -40°C / +95°C Shore : 65
Part N° |
Shore |
Packaging |
3035150000000 |
65 |
10 |
Full bore : 20 mm Temperature : -40°C / +200°C Shore : 60 Conditions of use : Steam
Part N° |
Shore |
Packaging |
3035200000000 |
60 |
10 |
Size :Ø 34 x height 10,5 mm Full bore: 20 mm Temperature : -40°C / +95°C Shore : 50
Part N° |
Shore |
Packaging |
3035190000000 |
50 |
100 |
- Material : Perbunan - Resistance : Oil - Medium : Air c. - Colour : Black - Shore : 60 - Symb. : SGOR - Temperature : - 40 °C / + 95 °C
Part N° |
Model |
Ø external |
Height |
Shore |
Packaging |
3035170000000 |
SGOR |
33 |
7 |
60 |
50 |
- Material : Ohasil - Resistance : Steam - Medium : Steam - Colour : Natural - Shore : 75 - Symb. : SDORN - Temperature : - 40 °C / + 200 °C
Part N° |
Model |
Ø external |
Height |
Shore |
Packaging |
3035140000000 |
SDOR-N |
30 |
4 |
75 |
10 |
- Full bore : 31 mm
Part N° |
Model |
Ø external |
Height |
Shore |
Packaging |
035220000000 |
SKD |
48,5 |
10,5 |
60 |
10 |
Standard : NF E29-573 Conditions of use : Water, compressed air, oil Temperatures : -10°C/+70°C
Part N° |
Ø |
Packaging |
2005140000000 |
|
10 |
Standard : NF E29-573 Conditions of use : Water, compressed air Temperatures : -10°C +90°C
Part N° |
Full bore |
PN |
Packaging |
2005150000000 |
15 |
10 |
120 |
Part N° |
Ø |
Ø external |
PN |
Packaging |
3005150001700 |
17 |
16-18 |
10 |
10 |
3005150003600 |
36 |
34-37 |
10 |
10 |
3005150003800 |
38 |
37-38 |
10 |
10 |
Part N° |
Ø |
Ø external |
PN |
Packaging |
3015150001700 |
17 |
16-18 |
10 |
10 |
3015150002000 |
20 |
19-21 |
10 |
10 |
3015150002300 |
23 |
22-24 |
10 |
10 |
3015150002600 |
26 |
25-27 |
10 |
10 |
3015150002900 |
29 |
28-30 |
10 |
10 |
3015150003200 |
32 |
31-33 |
10 |
10 |
3015150003600 |
36 |
34-37 |
10 |
10 |
3015150003800 |
38 |
37-39 |
10 |
10 |
Material : galvanized steel Wire : Ø3 mm Part N° : 3035650000000
For connection blasting hose Thread ISO 228-1 et Coarse Thread Series Body : Aluminium Pressure : PN 12 bar
Part N° |
Model |
Tuyau |
Thread |
L (mm) |
PN |
Packaging |
3032870323200 |
SD32-32A |
32 x 8 |
G1"1/4 |
130 |
12 |
1 |
3032870503200 |
SD 50-32A |
32 x 8 |
Coarse thread 50 mm |
130 |
12 |
1 |
Air King couplings : American-type - CROWFOOT COUPLING
This range of couplings is intended for compressed air pipes used at ambient temperature and a pressure of 10 bar. It is advisable to use the safety pin provided with the coupling to avoid any accidental disconnection. Furthermore, a safety cable fitted with two eyes may be installed on the connection between two hoses.
|